Blaupunkt RDM 127 operating instructions Adjusting DNC, DNC-ADJUST Stop

Page 56

DNC – Dynamic Noise Covering

With the help of DNC it is possible to enjoy the same volume while driving that you find pleasant in the stationary vehicle.

The volume is increased at different rates for different frequency bands, depend- ing on the noise in the moving vehicle.

In this way, the volume and the sound balance remain pleasant to the ear, re- gardless of whether the vehicle noise increases or decreases. Noise of very short duration, e.g. crossing railway tracks, is ignored.

Adjusting DNC

S

For DNC to operate correctly, it is necessary to first perform a calibration proce- dure with the help of a microphone. Using the enclosed self-adhesive Velcro tape, install the microphone permanently in the immediate vicinity of the console, but not close to sources of noise such as heating vents and air-conditioning.

The mouth of the microphone must face into the passenger area. Select a quiet area for the calibration and switch the engine off.

Press S briefly.

Press DNC for approximately 1 second. DNC-ADJUSTwill appear in the display header.

The DNC calibration procedure has begun and will run through automatically. You can abort the procedure by

pressing STOP .

As soon as DNC-ADJUST READY appears in the display, the calibration proce- dure has been completed.

DNC-ADJUST 10

STOP

56

Image 56
Contents New York RDM Table of contents Traffic safetyPrecautions InstallationAccessories Important informationRemote control RC OptionalOn / Mute Switching on/off Quick referenceTU tuner CDC CD changerCD eject Open/close panel. Eject/insert CD Softkeys Display/Selection menuDisplay header Additional functions for the rocker switch = Multi-functional rocker switch or remote control butTons optional Radio mode Inserting the KeyCard Flashing KeyCard tongueKeyCard anti-theft system Starting up the unitDSC-MAIN Menu Removing the KeyCardTraining the second KeyCard / replacing the KeyCard Turn On Message T.O.M Displaying the radio pass dataShort Additional Memory S.A.M Taking care of your KeyCard Switching off the flashing lightOptical indication of anti-theft protection First-time installation First Install Clock OWNER-ID AUX-IN Norm SET ExitSetting the clock Detailed operating instructionsAUX-NAME Exit L K M a N Clear Exit OWNER-ID Clear Exit First InstallAUX Resetting to original factory settings Selecting the waveband Switching to the radio modeRadio operation with RDS Radio Data System Switching from the reception table to the preference table Selecting a stationNDR NDR1 NDSLocal Store ExitBy station search or manually Start the station search function by pressingA N With ScanStart Scan End ScanStoring stations Store Exit NDR Search Bremen ScanFM stations Select reception table to store stationsDeleting stored station Local DX StoreStoring MW/LW stations Select search menu to store stationsSearch Scan Antenne NDR2 MDR Life NDR1 NDS Brocken Station nameAlternative frequency Switching the regional programme function on/off REG Regional programmesPTY NDR1 NDS REG-E Text RegionalSwitching the PTY menu on/off PTY PTY Menu NewsAffairs InfoProgramme type PTY Menu NewsAffairs Switching PTY on / Selecting the programme typeActivate Giving radio stations a name Enter Clear ExitSwitching traffic announcement priority on/off Traffic message reception with RDS-EONSearch Scan Bremen 1 Bremen Bremen 3 HR 3 NDR1 NDSSwitching the warning beep off Automatic start of station searchPTY Traffic Message TA OFF ExitTreble Bass Fader Balance Exit Adjusting the volume for traffic announcementsAdjusting the sound stage for traffic messages and TIM Your motor antenna may be damaged in a car wash Traffic Memo TIMTIM Active Setting the exact time Hours Hours + MIN MIN + ExitDisplaying the time Correcting the timeProgramming the TIM standby mode / TIM times TimerHours Hours + MIN Timer TimerHours Hours + MIN MIN + Timer Recalling stored traffic messagesActive Exit TIM NDR CUETIM standby mode while the radio is switched off Switching the TIM standby mode on/offTIM Active Timer ActiveTIM Active TIM-FUNCTION Deactivated Switching to the CD mode Operating the CD playerInserting a CD MIX CD Name Scan Repeat TPM TPM CLREjecting a CD Selecting a trackMIX Scan Repeat TPM TPM CLR MIX CD NameScan Repeat TPM TPM CLRRepeating a track Repeat MIX CD Name ScanRepeat TPM TPM CLR TPM Programmed MIX CD Name Scan RepeatDeleting the TPM memory TPM CLR MIX CD Name Scan RepeatTPM TPM CLR TPM Track Clrd MIX CD Name Scan RepeatGiving CDs a name CDC Name Clear Exit V a L DSelecting the display mode TRACK/TIME Deleting the name of a CD CD NameSwitching to the CD changer mode Operating a CD changer optionalDisc Empty DiscSelecting a CD and a track Display header will indicate the current selectionMIX Disc Scan Time Repeat TPM TPM CLR Scan TR MIX CDC NameTPM TPM CLR Repeat a CD or a track RepeatRepeat Track MIX CDC Name Scan Time TPM Programmed MIX CDC Name Scan Time Repeat TPM CLR Disc TPM CLR TPM Track Clrd MIX CDC Name Scan Time RepeatDeleting the TPM memory for all of the magazines TPM Disc Clrd MIX CDC Name Scan Time RepeatTPM CLR Prev CD Next CD Clear Exit Prev Next CD Clear Exit L D Deleting the name of a CD CDC NameL D MIX CDC Name Scan Track Repeat TPM TPM CLR AUX mode Switching on AUXAudio settings Bass, treble, balance, faderLoudness Treble +5 Bass DNC Fader Balance Exit Loudness Loudness onAdjusting DNC DNC-ADJUST StopAdjusting DNC sensitivity DNC-LEVEL MID Treble BassDNC Fader Balance Exit LoudnessEQ Equalizer Equalizer Menu AUTO-EQ1 View EQAUTO-EQ2 AUTO-EQ3 MAN-EQ Exit EQ OFFHi-fi calibration Start Hi-fi calibrationYesno View AUTO-EQ Front Left Next Exit Checking/altering Hi-fi calibrationSET AUTO-EQ Front Left Calling up the Hi-fi calibrationSetting the equalizer manually Calling up the manual equalizer settingProgramming with DSC Car radios have been pre-programmed at the factoryTable Size MENU-OFF AngleLoudness Exit Scantime DSC-VARIOUS Menu Clock VOL FIX BeepKC LED DSC-KEYCARD Learn KC Read KC Exit VOL FIXMuting the audio source while using the car phone CD player SpecificationsTuner Blaupunkt telephone hotline Bosch Gruppe