Blaupunkt RDM 127 operating instructions SET AUTO-EQ Front Left, Calling up the Hi-fi calibration

Page 61

•Press << / >> to select the frequency band you wish to correct, e.g. 1 kHz. The selected frequency band will appear in the bottom line.

•Press / to adjust the frequency range as desired.

After completing the adjustments, press NEXT and adjust the loudspeaker on the front right, rear left and rear right.

If necessary, adjust the other channels as described above.

•Press EXIT to exit the menu.

Die letzte Einstellung ist automatisch gespeichert.

Note:

During the calibration procedure, loudspeakers should be hooked up to all four connections.

If one of the loudspeakers is not detected during calibration because it is defec- tive, not connected or obstructed, then a linear equalizer control will be done for this loudspeaker pair.

The balance/fader settings can be adjusted in a limited range only.

Calling up the Hi-fi calibration

If you want the playback to function according to the Hi-fi calibration,

•press S, EQ and the corresponding softkey (AUTO-EQ1 ... AUTO-EQ3) one after the other.

S

SET AUTO-EQ 2

FRONT LEFT

------------------

NEXT 1k HZ EXIT

61

DEUTSCH

ENGLISH

FRANÇAIS

ITALIANO

NEDERLANDS

SVENSKA

ESPAÑOL

PORTUGUÊS

 

 

 

 

 

 

 

 

Page 60 Page 62
Image 61
Page 60 Page 62
Contents
New York RDM Traffic safety Table of contentsInstallation PrecautionsAccessories Important informationOptional Remote control RCQuick reference On / Mute Switching on/offCDC CD changer TU tunerDisplay header Display/Selection menuCD eject Open/close panel. Eject/insert CD Softkeys Tons optional Radio mode = Multi-functional rocker switch or remote control butAdditional functions for the rocker switch Flashing KeyCard tongue Inserting the KeyCardStarting up the unit KeyCard anti-theft systemTraining the second KeyCard / replacing the KeyCard Removing the KeyCardDSC-MAIN Menu Short Additional Memory S.A.M Displaying the radio pass dataTurn On Message T.O.M Optical indication of anti-theft protection Switching off the flashing lightTaking care of your KeyCard First Install Clock OWNER-ID AUX-IN Norm SET Exit First-time installationSetting the clock Detailed operating instructionsAUX OWNER-ID Clear Exit First InstallAUX-NAME Exit L K M a N Clear Exit Resetting to original factory settings Radio operation with RDS Radio Data System Switching to the radio modeSelecting the waveband Selecting a station Switching from the reception table to the preference tableNDR NDR1 NDSStore Exit LocalBy station search or manually Start the station search function by pressingWith Scan A NStart Scan End ScanStore Exit NDR Search Bremen Scan Storing stationsFM stations Select reception table to store stationsLocal DX Store Deleting stored stationStoring MW/LW stations Select search menu to store stationsAlternative frequency Station nameSearch Scan Antenne NDR2 MDR Life NDR1 NDS Brocken REG Regional programmes Switching the regional programme function on/offPTY NDR1 NDS REG-E Text RegionalPTY PTY Menu News Switching the PTY menu on/offAffairs InfoPTY Menu News Programme typeActivate Switching PTY on / Selecting the programme typeAffairs Enter Clear Exit Giving radio stations a nameTraffic message reception with RDS-EON Switching traffic announcement priority on/offSearch Scan Bremen 1 Bremen Bremen 3 HR 3 NDR1 NDSAutomatic start of station search Switching the warning beep offPTY Traffic Message TA OFF ExitAdjusting the sound stage for traffic messages and TIM Adjusting the volume for traffic announcementsTreble Bass Fader Balance Exit TIM Active Traffic Memo TIMYour motor antenna may be damaged in a car wash Hours Hours + MIN MIN + Exit Setting the exact timeDisplaying the time Correcting the timeTimer Programming the TIM standby mode / TIM timesHours Hours + MIN Timer TimerRecalling stored traffic messages Hours Hours + MIN MIN + TimerActive Exit TIM NDR CUESwitching the TIM standby mode on/off TIM standby mode while the radio is switched offTIM Active Timer ActiveTIM Active TIM-FUNCTION Deactivated Operating the CD player Switching to the CD modeInserting a CD MIX CD Name Scan Repeat TPM TPM CLRSelecting a track Ejecting a CDScan Repeat TPM TPM CLR MIX CD Name MIXScan Repeat TPM TPM CLRMIX CD Name Scan Repeating a track RepeatRepeat TPM TPM CLR TPM Programmed MIX CD Name Scan RepeatMIX CD Name Scan Repeat Deleting the TPM memory TPM CLRTPM TPM CLR TPM Track Clrd MIX CD Name Scan RepeatClear Exit V a L D Giving CDs a name CDC NameDeleting the name of a CD CD Name Selecting the display mode TRACK/TIMEOperating a CD changer optional Switching to the CD changer modeDisc Empty DiscDisplay header will indicate the current selection Selecting a CD and a trackScan Time Repeat TPM TPM CLR Scan TR MIX CDC Name MIX DiscRepeat Track MIX CDC Name Scan Time Repeat a CD or a track RepeatTPM TPM CLR TPM CLR TPM Track Clrd MIX CDC Name Scan Time Repeat TPM Programmed MIX CDC Name Scan Time Repeat TPM CLR DiscTPM CLR Prev CD Next CD Clear Exit TPM Disc Clrd MIX CDC Name Scan Time RepeatDeleting the TPM memory for all of the magazines L D Deleting the name of a CD CDC NamePrev Next CD Clear Exit L D MIX CDC Name Scan Track Repeat TPM TPM CLR Switching on AUX AUX modeBass, treble, balance, fader Audio settingsLoudness Treble +5 Bass DNC Fader Balance Exit Loudness Loudness onDNC-ADJUST Stop Adjusting DNC DNC-LEVEL MID Treble Bass Adjusting DNC sensitivity DNC Fader Balance Exit LoudnessEqualizer Menu AUTO-EQ1 View EQ EQ EqualizerAUTO-EQ2 AUTO-EQ3 MAN-EQ Exit EQ OFFStart Hi-fi calibration Hi-fi calibrationChecking/altering Hi-fi calibration Yesno View AUTO-EQ Front Left Next ExitCalling up the Hi-fi calibration SET AUTO-EQ Front LeftCalling up the manual equalizer setting Setting the equalizer manuallyCar radios have been pre-programmed at the factory Programming with DSCTable Size Angle MENU-OFFKC LED DSC-VARIOUS Menu Clock VOL FIX BeepLoudness Exit Scantime VOL FIX DSC-KEYCARD Learn KC Read KC ExitMuting the audio source while using the car phone Tuner SpecificationsCD player Bosch Gruppe Blaupunkt telephone hotline
Top Page Image Contents