Blaupunkt RDM 127 operating instructions KeyCard anti-theft system, Starting up the unit

Page 10

The KeyCard anti-theft system

One KeyCard is included with the set.

You can, however, also use a second KeyCard with your set. You can purchase a second KeyCard at any specialised dealership.

Starting up the unit

Press ON to switch the set on.

With the KeyCard tongue protruding out of its opening, insert the KeyCard into the slot with the contact area facing up. Make sure that the KeyCard is inserted properly.

The car radio is now ready to operate.

If a KeyCard which does not belong to the set is inserted, KEYCARD ERROR will appear in the display. Do not attempt to use the equipment in this case.

After approximately 10 seconds the unit will switch off automatically.

If you insert any other type of card (e.g. telephone or credit card) into the slot, the display will indicate THIS IS NO KEYCARD for approximately 2 seconds.

Remove the incorrect card and insert the correct KeyCard into the unit. Following KEYCARD ERROR or THIS IS NO KEYCARD

press ON to switch the unit on.

KeyCard

10

Image 10
Contents New York RDM Table of contents Traffic safetyAccessories PrecautionsInstallation Important informationRemote control RC OptionalOn / Mute Switching on/off Quick referenceTU tuner CDC CD changerDisplay header Display/Selection menuCD eject Open/close panel. Eject/insert CD Softkeys Tons optional Radio mode = Multi-functional rocker switch or remote control butAdditional functions for the rocker switch Inserting the KeyCard Flashing KeyCard tongueKeyCard anti-theft system Starting up the unitTraining the second KeyCard / replacing the KeyCard Removing the KeyCardDSC-MAIN Menu Short Additional Memory S.A.M Displaying the radio pass dataTurn On Message T.O.M Optical indication of anti-theft protection Switching off the flashing lightTaking care of your KeyCard Setting the clock First-time installationFirst Install Clock OWNER-ID AUX-IN Norm SET Exit Detailed operating instructionsAUX OWNER-ID Clear Exit First InstallAUX-NAME Exit L K M a N Clear Exit Resetting to original factory settings Radio operation with RDS Radio Data System Switching to the radio modeSelecting the waveband NDR Switching from the reception table to the preference tableSelecting a station NDR1 NDSBy station search or manually LocalStore Exit Start the station search function by pressingStart Scan A NWith Scan End ScanFM stations Storing stationsStore Exit NDR Search Bremen Scan Select reception table to store stationsStoring MW/LW stations Deleting stored stationLocal DX Store Select search menu to store stationsAlternative frequency Station nameSearch Scan Antenne NDR2 MDR Life NDR1 NDS Brocken PTY NDR1 NDS REG-E Text Switching the regional programme function on/offREG Regional programmes RegionalAffairs Switching the PTY menu on/offPTY PTY Menu News InfoProgramme type PTY Menu NewsActivate Switching PTY on / Selecting the programme typeAffairs Giving radio stations a name Enter Clear ExitSearch Scan Switching traffic announcement priority on/offTraffic message reception with RDS-EON Bremen 1 Bremen Bremen 3 HR 3 NDR1 NDSPTY Traffic Message Switching the warning beep offAutomatic start of station search TA OFF ExitAdjusting the sound stage for traffic messages and TIM Adjusting the volume for traffic announcementsTreble Bass Fader Balance Exit TIM Active Traffic Memo TIMYour motor antenna may be damaged in a car wash Displaying the time Setting the exact timeHours Hours + MIN MIN + Exit Correcting the timeHours Hours + MIN Timer Programming the TIM standby mode / TIM timesTimer TimerActive Exit TIM NDR Hours Hours + MIN MIN + TimerRecalling stored traffic messages CUETIM Active Timer TIM standby mode while the radio is switched offSwitching the TIM standby mode on/off ActiveTIM Active TIM-FUNCTION Deactivated Inserting a CD Switching to the CD modeOperating the CD player MIX CD Name Scan Repeat TPM TPM CLREjecting a CD Selecting a trackScan MIXScan Repeat TPM TPM CLR MIX CD Name Repeat TPM TPM CLRRepeat Repeating a track RepeatMIX CD Name Scan TPM TPM CLR TPM Programmed MIX CD Name Scan RepeatTPM Deleting the TPM memory TPM CLRMIX CD Name Scan Repeat TPM CLR TPM Track Clrd MIX CD Name Scan RepeatGiving CDs a name CDC Name Clear Exit V a L DSelecting the display mode TRACK/TIME Deleting the name of a CD CD NameDisc Empty Switching to the CD changer modeOperating a CD changer optional DiscSelecting a CD and a track Display header will indicate the current selectionMIX Disc Scan Time Repeat TPM TPM CLR Scan TR MIX CDC NameRepeat Track MIX CDC Name Scan Time Repeat a CD or a track RepeatTPM TPM CLR TPM Programmed MIX CDC Name Scan Time Repeat TPM CLR Disc TPM CLR TPM Track Clrd MIX CDC Name Scan Time RepeatTPM CLR Prev CD Next CD Clear Exit TPM Disc Clrd MIX CDC Name Scan Time RepeatDeleting the TPM memory for all of the magazines L D Deleting the name of a CD CDC NamePrev Next CD Clear Exit L D MIX CDC Name Scan Track Repeat TPM TPM CLR AUX mode Switching on AUXLoudness Audio settingsBass, treble, balance, fader Treble +5 Bass DNC Fader Balance Exit Loudness Loudness onAdjusting DNC DNC-ADJUST StopDNC Adjusting DNC sensitivityDNC-LEVEL MID Treble Bass Fader Balance Exit LoudnessAUTO-EQ2 EQ EqualizerEqualizer Menu AUTO-EQ1 View EQ AUTO-EQ3 MAN-EQ Exit EQ OFFHi-fi calibration Start Hi-fi calibrationYesno View AUTO-EQ Front Left Next Exit Checking/altering Hi-fi calibrationSET AUTO-EQ Front Left Calling up the Hi-fi calibrationSetting the equalizer manually Calling up the manual equalizer settingProgramming with DSC Car radios have been pre-programmed at the factoryTable Size MENU-OFF AngleKC LED DSC-VARIOUS Menu Clock VOL FIX BeepLoudness Exit Scantime DSC-KEYCARD Learn KC Read KC Exit VOL FIXMuting the audio source while using the car phone Tuner SpecificationsCD player Blaupunkt telephone hotline Bosch Gruppe