Alpine CDA-9853 Setting the Time Correction Unit, Adjusting and Storing the Time Correction

Time Difference Table

Delay	Time	Distance	Distance	Delay	Time	Distance	Distance
	Difference				Difference
Number		(cm)	(inch)	Number		(cm)	(inch)
	(ms)				(ms)
0	0.0	0.0	0.0	51	5.1	173.4	68.3
1	0.1	3.4	1.3	52	5.2	176.8	69.7
2	0.2	6.8	2.7	53	5.3	180.2	71.0
3	0.3	10.2	4.0	54	5.4	183.6	72.4
4	0.4	13.6	5.4	55	5.5	187.0	73.7
5	0.5	17.0	6.7	56	5.6	190.4	75.0
6	0.6	20.4	8.0	57	5.7	193.8	76.4
7	0.7	23.8	9.4	58	5.8	197.2	77.7
8	0.8	27.2	10.7	59	5.9	200.6	79.1
9	0.9	30.6	12.1	60	6.0	204.0	80.4
10	1.0	34.0	13.4	61	6.1	207.4	81.7
11	1.1	37.4	14.7	62	6.2	210.8	83.1
12	1.2	40.8	16.1	63	6.3	214.2	84.4
13	1.3	44.2	17.4	64	6.4	217.6	85.8
14	1.4	47.6	18.8	65	6.5	221.0	87.1
15	1.5	51.0	20.1	66	6.6	224.4	88.4
16	1.6	54.4	21.4	67	6.7	227.8	89.8
17	1.7	57.8	22.8	68	6.8	231.2	91.1
18	1.8	61.2	24.1	69	6.9	234.6	92.5
19	1.9	64.6	25.5	70	7.0	238.0	93.8
20	2.0	68.0	26.8	71	7.1	241.4	95.1
21	2.1	71.4	28.1	72	7.2	244.8	96.5
22	2.2	74.8	29.5	73	7.3	248.2	97.8
23	2.3	78.2	30.8	74	7.4	251.6	99.2
24	2.4	81.6	32.2	75	7.5	255.0	100.5
25	2.5	85.0	33.5	76	7.6	258.4	101.8
26	2.6	88.4	34.8	77	7.7	261.8	103.2
27	2.7	91.8	36.2	78	7.8	265.2	104.5
28	2.8	95.2	37.5	79	7.9	268.6	105.9
29	2.9	98.6	38.9	80	8.0	272.0	107.2
30	3.0	102.0	40.2	81	8.1	275.4	108.5
31	3.1	105.4	41.5	82	8.2	278.8	109.9
32	3.2	108.8	42.9	83	8.3	282.2	111.2
33	3.3	112.2	44.2	84	8.4	285.6	112.6
34	3.4	115.6	45.6	85	8.5	289.0	113.9
35	3.5	119.0	46.9	86	8.6	292.4	115.2
36	3.6	122.4	48.2	87	8.7	295.8	116.6
37	3.7	125.8	49.6	88	8.8	299.2	117.9
38	3.8	129.2	50.9	89	8.9	302.6	119.3
39	3.9	132.6	52.3	90	9.0	306.0	120.6
40	4.0	136.0	53.6	91	9.1	309.4	121.9
41	4.1	139.4	54.9	92	9.2	312.8	123.3
42	4.2	142.8	56.3	93	9.3	316.2	124.6
43	4.3	146.2	57.6	94	9.4	319.6	126.0
44	4.4	149.6	59.0	95	9.5	323.0	127.3
45	4.5	153.0	60.3	96	9.6	326.4	128.6
46	4.6	156.4	61.6	97	9.7	329.8	130.0
47	4.7	159.8	63.0	98	9.8	333.2	131.3
48	4.8	163.2	64.3	99	9.9	336.6	132.7
49	4.9	166.6	65.7
50	5.0	170.0	67.0

Setting the Time Correction Unit

You can change the unit, (ms, cm or inch) of time correction.

1Press MENU.

2Select SETUP by sliding your finger on the GlideTouch bar to the left or right. Press the GlideTouch bar under SETUP.

The main SETUP menu is displayed.

3Select DISP (DISPLAY) by sliding your finger on the GlideTouch bar to the left or right. Press the GlideTouch bar under DISP (DISPLAY).

The DISPLAY SETUP menu is displayed.

4Select T.CORR (T.CORR PAR) by sliding your finger on the GlideTouch bar to the left or right.

Press the GlideTouch bar under T.CORR (T.CORR PAR).

5Select ms (MS), cm (CM) or inch (INCH) by sliding your finger on the GlideTouch bar to the left or right. Press under ms (MS), cm (CM) or inch (INCH) on the GlideTouch bar.

6After setting, press and hold MENU for at least 2 seconds to return to normal mode.

•If MENU is pressed while adjusting or setting the itmes in the MENU mode, the unit will return to the previous selection secreen.

•By pressing the GlideTouch bar under RETURN in the MENU mode, the unit will return to the normal mode.

Adjusting and Storing the Time Correction

Before performing the following procedures, refer to “About Time Correction” (page 19).

1Press and hold MENU for at least 2 seconds.

2Select Time Correction (T.CORR) mode by sliding your finger on the GlideTouch bar to the left or right. Press the GlideTouch bar under Time Correction (T.CORR).

3Press BAND to select a speaker to be adjusted.

F-L → F-R → R-L → R-R → SW-L (S-L) → SW-R (S-R) → F-L

4Adjust the time difference (0.0 to 9.9 ms) or distance by sliding your finger on the GlideTouch bar to the left or right. Or turn the Rotary encoder to adjust the time difference.

5Repeat steps 3 and 4 to set another speaker.

6When the setting has been completed, press FUNC. or the GlideTouch bar to activate the preset mode.

20-EN