Alpine CDA-9853, CDA-9855 Adjusting and Storing the Crossover Settings, WAY System, 18-EN

Page 19

Adjusting and Storing the Crossover Settings

Before performing the following procedures, refer to “About the Crossover” (Page 17).

1Press and hold MENU for at least 2 seconds.

2Select the Crossover (X-OVER) mode by sliding your finger on the GlideTouch bar to the left or right. Press the GlideTouch bar under the Crossover (X-OVER) mode.

2WAY System

3Press BAND to select the band to be adjusted.

LOW → MID → HIGH → LOW

(SUBW) (REAR) (FRONT) (SUBW)

4Select the desired cut-off frequency (Crossover Point) by sliding your finger on the GlideTouch bar to the left or right.

Adjustable frequency bands: 20Hz to 200Hz

(in 1/3 octave steps)

5Press SOURCE/POWER to adjust the slope.

Adjustable slope: 0 (FLAT), 1 (6dB/oct.), 2 (12dB/oct.) 3 (18dB/oct.) 4 (24dB/oct.)

6Adjust the output level by turning the Rotary encoder.

Adjustable output level: -12 to 0 dB.

7To adjust another band, repeat steps 3 to 6, then adjust all bands.

8When the setting has been completed, press FUNC. or the GlideTouch bar to activate the preset mode.

9Select any one of the preset numbers (1 through 6) by sliding your finger on the GlideTouch bar to the left or right. Press and hold the GlideTouch bar under the desire preset for at least 2 seconds to store the adjusted contents.

10After setting, press and hold MENU for at least 2 seconds to return to normal mode.

•If MENU is pressed while adjusting or setting the itmes in the MENU mode, the unit will return to the previous selection secreen.

•By pressing the GlideTouch bar under RETURN in the MENU mode, the unit will return to the normal mode.

•If no peration is performed in 60 seconds, the unit will return to the normal mode.

3 WAY System

3Press BAND to select the band to be adjusted.

LOW → MID-L → MID-H → HIGH → LOW

4Select the desired cut-off frequency (Crossover Point) by sliding your finger on the GlideTouch bar to the left or right.

Adjustable frequency bands:

LOW: 20Hz to 200Hz (in 1/3 octave steps)

MID-L: 20Hz to 200Hz (in 1/3 octave steps)

MID-H: 20Hz to 20kHz (in 1/3 octave steps)

HIGH: 1kHz to 20 kHz (in 1/3 octave steps)

5Press SOURCE/POWER to adjust the slope.

Adjustable slope: 0 (FLAT)*1, 1 (6dB/oct.), 2 (12dB/oct.) 3 (18dB/oct.), 4 (24dB/oct.)

*FLAT can be set for the HIGH slope only when USER'S is selected in “Setting the Response Slope for the High Range Speaker (TW SETUP)” (page 29). Depending on the response characteristics of the speaker, care should be taken when setting the response slope to FLAT, as speaker damage may result. With the CDA-9855, a message is displayed when the response slope for the high range speaker is set to FLAT.

6Adjust the output level by turning the Rotary encoder.

Adjustable output level: -12 to 0 dB.

7To adjust another band, repeat steps 3 to 6, then adjust all bands.

8When the setting has been completed, press FUNC. or the GlideTouch bar to activate the preset mode.

9Select any one of the preset numbers (1 through 6) by sliding your finger on the GlideTouch bar to the left or right. Press and hold the GlideTouch bar under the desire preset for at least 2 seconds to store the adjusted contents.

10After setting, press and hold MENU for at least 2 seconds to return to normal mode.

•If MENU is pressed while adjusting or setting the itmes in the MENU mode, the unit will return to the previous selection secreen.

•By pressing the GlideTouch bar under RETURN in the MENU mode, the unit will return to the normal mode.

•If no peration is performed in 60 seconds, the unit will return to the normal mode.

•About the 2way/3way system

You can switch to 2way/3way system mode with the 2way/3way switch on the bottom side of the unit (pages 45 to 47).

 

 

 

 

When setting to “3 WAY”:

F/R Sub-W

 

 

 

The unit can be operated in a 3 way system.

3WAY

 

 

 

When setting to “F/R/Sub-W”:

 

 

 

 

 

 

 

 

The unit can be operated in a 2 way system.

18-EN

Page 18 Page 20
Image 19
Page 18 Page 20
Contents CDA-9855 CDA-9853 Contents Installation and Connections Operating Instructions Never Attempt the Following On handling Compact Discs CD/CD-R/CD-RW Touch or press the desired position on the GlideTouch bar About the GlideTouch Bar OperationMove your finger on the GlideTouch bar to the left or right Getting Started Turning Power On and OffSetting Time CDA-9853 only Press SOURCE/POWER to turn on the unitOpening and Closing the Movable Display Adjusting VolumeDisplay Tilt Adjustment Lowering Volume QuicklyChanging the Radio Frequencies for each Country Manual Storing of Station PresetsAutomatic Memory of Station Presets RadioFreqency Search Function Tuning to Preset StationsCD / MP3 / WMA Station Title Search Function11-EN Press FUNC. to activate the audio function modePress the Glide Touch bar under RPT to select the RPT mode Repeat PlayFile/Folder Name Search concerning MP3/ WMA X. Random PlayScanning Programs Searching from CD TextAbout MP3/WMA Folder Name Search modeFile Name Search mode Quick Search14-EN Terminology15-EN Sound SettingEqualizer Presets Setting Users EQ modeAdjusting and Storing the Graphic Equalizer Curve Adjusting and Storing the Parametric Equalizer Curve16-EN 17-EN Way modeRecalling the Stored Equalizer Curve About the CrossoverWAY System Adjusting and Storing the Crossover SettingsPress SOURCE/POWER to adjust the slope Adjust the output level by turning the Rotary encoderExample 2. Listening Position All Seats Recalling the Stored Crossover SettingsAbout Time Correction Example 1. Listening Position Front Left Seat20-EN Setting the Time Correction UnitAdjusting and Storing the Time Correction Display Setup menu is displayedSetting the MX Mode Recalling the Stored Time Correction Settings21-EN Press Title Other FunctionsDisplaying the Title/Text 22-ENTitle About the indicator display CDA-9853 only23-EN About Title and TextDisplaying Time Blackout Mode On and Off CDA-9855 onlyTitling Discs/Stations Erasing Disc Title/Station TitleIf a 4ch Amplifier is Connected Setting Amplifier LinkDisplaying the External Amplifier Information If a Mono Amplifier is ConnectedIf you want to use colors other than the above About i-Personalize26-EN 27-EN Data DownloadingData downloading starts 28-EN General SettingAudio Setting Tuner Setting29-EN Demo Setting Display Setting30-EN Checking the SAT Radio ID Number Storing Channel PresetsSAT Radio Receiver Optional Receiving Channels with the SAT Radio Receiver OptionalChanging the Display Receiving Stored ChannelsQuick Search Function Channel/Category Search Function33-EN Setting the Auxiliary Data Field Display34-EN Searching for a desired SongSearching by Playlist Searching by artist nameTo search for an album of the selected artist Random Play Shuffle M.I.XSearching by album name 35-ENEach press changes the display Displaying the Text36-EN Song will be played back repeatedlyMulti-Changer Selection Optional Changer OptionalControlling CD Changer Optional Playing MP3 Files with the CD Changer Optional38-EN Remote ControlControls on Remote Control Operating the Audio ProcessorBasic Battery ReplacementInformation Case of Difficulty40-EN Indication for CD PlayerCall Indication for SAT Receiver ModeIndication for CD Changer 41-ENIndication for iPod Mode Specifications42-EN 43-EN Installation and ConnectionsRemoval Installation44-EN Slide the mounting sleeve into the dashboard45-EN Connections46-EN Amplifier Link ConnectorTo prevent noise/interference in the audio system 47-ENCHA-1214 CHM-S630 CHA-S634Limited Warranty Page Page Page
Top Page Image Contents