Alpine CDA-9855, CDA-9853 owner manual Installation and Connections, 43-EN

Page 44

Installation and Connections

Before installing or connecting the unit, please read the following and pages 3 to 5 of this manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury.

If swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.

Precautions

•Be sure to disconnect the cable from the (–) battery post before installing your CDA-9855/CDA-9853. This will reduce any chance of damage to the unit in case of a short-circuit.

•Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle's electrical system.

•When making connections to the vehicle's electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the CDA-9855/CDA-9853 to the fuse box, make sure the fuse for the intended circuit of the CDA-9855/CDA-9853 has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer.

•The CDA-9855/CDA-9853 uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized ALPINE dealer for assistance.

•Be sure to connect the speaker (–) leads to the speaker (–) terminal. Never connect left and right channel speaker cables to each other or to the vehicle body.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit.

SERIAL NUMBER:

INSTALLATION DATE: INSTALLATION TECHNICIAN: PLACE OF PURCHASE:

43-EN

Page 43 Page 45
Image 44
Page 43 Page 45
Contents CDA-9855 CDA-9853 Contents Installation and Connections Operating Instructions Never Attempt the Following On handling Compact Discs CD/CD-R/CD-RW Move your finger on the GlideTouch bar to the left or right About the GlideTouch Bar OperationTouch or press the desired position on the GlideTouch bar Turning Power On and Off Setting Time CDA-9853 onlyPress SOURCE/POWER to turn on the unit Getting StartedAdjusting Volume Display Tilt AdjustmentLowering Volume Quickly Opening and Closing the Movable DisplayManual Storing of Station Presets Automatic Memory of Station PresetsRadio Changing the Radio Frequencies for each CountryTuning to Preset Stations CD / MP3 / WMAStation Title Search Function Freqency Search FunctionPress FUNC. to activate the audio function mode Press the Glide Touch bar under RPT to select the RPT modeRepeat Play 11-ENX. Random Play Scanning ProgramsSearching from CD Text File/Folder Name Search concerning MP3/ WMAFolder Name Search mode File Name Search modeQuick Search About MP3/WMATerminology 14-ENSound Setting Equalizer PresetsSetting Users EQ mode 15-EN16-EN Adjusting and Storing the Parametric Equalizer CurveAdjusting and Storing the Graphic Equalizer Curve Way mode Recalling the Stored Equalizer CurveAbout the Crossover 17-ENAdjusting and Storing the Crossover Settings Press SOURCE/POWER to adjust the slopeAdjust the output level by turning the Rotary encoder WAY SystemRecalling the Stored Crossover Settings About Time CorrectionExample 1. Listening Position Front Left Seat Example 2. Listening Position All SeatsSetting the Time Correction Unit Adjusting and Storing the Time CorrectionDisplay Setup menu is displayed 20-EN21-EN Recalling the Stored Time Correction SettingsSetting the MX Mode Other Functions Displaying the Title/Text22-EN Press TitleAbout the indicator display CDA-9853 only 23-ENAbout Title and Text TitleBlackout Mode On and Off CDA-9855 only Titling Discs/StationsErasing Disc Title/Station Title Displaying TimeSetting Amplifier Link Displaying the External Amplifier InformationIf a Mono Amplifier is Connected If a 4ch Amplifier is Connected26-EN About i-PersonalizeIf you want to use colors other than the above Data downloading starts Data Downloading27-EN General Setting 28-EN29-EN Tuner SettingAudio Setting 30-EN Display SettingDemo Setting Storing Channel Presets SAT Radio Receiver OptionalReceiving Channels with the SAT Radio Receiver Optional Checking the SAT Radio ID NumberReceiving Stored Channels Quick Search FunctionChannel/Category Search Function Changing the DisplaySetting the Auxiliary Data Field Display 33-ENSearching for a desired Song Searching by PlaylistSearching by artist name 34-ENRandom Play Shuffle M.I.X Searching by album name35-EN To search for an album of the selected artistDisplaying the Text 36-ENSong will be played back repeatedly Each press changes the displayChanger Optional Controlling CD Changer OptionalPlaying MP3 Files with the CD Changer Optional Multi-Changer Selection OptionalRemote Control Controls on Remote ControlOperating the Audio Processor 38-ENBattery Replacement InformationCase of Difficulty BasicIndication for CD Player 40-ENIndication for SAT Receiver Mode Indication for CD Changer41-EN Call42-EN SpecificationsIndication for iPod Mode Installation and Connections 43-ENInstallation 44-ENSlide the mounting sleeve into the dashboard RemovalConnections 45-ENAmplifier Link Connector 46-EN47-EN To prevent noise/interference in the audio systemCHA-S634 CHA-1214 CHM-S630Limited Warranty Page Page Page
Top Page Image Contents