Audio Authority Car Audio System How to Use These Tables, Sources, EQs and Amplifiers Speakers

Note that the front amps and speakers have matching group numbers as do the rear amps and speakers. As a rule, related amps and speakers have match- ing group numbers; this determines how the 902 Control Panel, if used, handles Volume Compensation of the products in these Groups. Figure 15 shows how the 902/903 Control Panel would arrange these product groups on its Product Group display windows.

B. Determine the Module ID settings.

Number the modules in each group to put the products in the desired order in the group. Use the following table for the appropriate module ID setting for each module.

ASD				SOURCES
å Demonstration Network
	Patents Pending
1	2	3	A	PROCESSOR/EQ
4	5	6	B	FRONT AMP
7	8	9	C
				FRONT SPEAKERS
	0		SECURE
				REAR AMP
	SilenTouch ™		Theft Alert
EQUAL VOLUME COMPARISON				REAR SPEAKERS
	ATTENUATION / SPL
ON / SPL
				SUB AMP
(STORE)			ATTEN.
	DECIBELS
MUTE			LEVEL
				SUBWOOFERS
(ADJUST)	P-NOISE	AUTO-CAL
			Model 902 Control Panel

Figure 15. This is how product groups appear on the 902 Control Panel.

The display shows which product in each group is selected.

Sources, EQs and Amplifiers							Speakers
Switching	Addressing		Set the MODULE ID to:			Addressing		Set the MODULE ID to:
Modules	Sequence for					Sequence for
910, 922,	Product		slide		rotary	932		slide	rotary
958, 942	Positions		switch		switch	Product Grps		switch	switch
1st module:	1	- 4	0 - 9		0	1 - 8		0 - 9	0
2nd module :	5	- 8	0 - 9		1	9 - 16		0 - 9	1
etc...	9	- 12	0 - 9		2	17 - 24		0 - 9	2
	13 - 16		0 - 9		3	25 - 32		0 - 9	3
	17 - 20		0 - 9		4	33 - 40		0 - 9	4
	21 - 24		0 - 9		5	41 - 48		0 - 9	5
	25 - 28		0 - 9		6	49 - 56		0 - 9	6
	29 - 32		0 - 9		7	57 - 64		0 - 9	7
	33 - 36		0 - 9		8	65 - 72		0 - 9	8
	37 - 40		0 - 9		9	73 - 80		0 - 9	9
	41	- 44	10 -	19	0	81 - 88		10 - 19	0
	45	- 48	10 -	19	1	89 - 96		10 - 19	1
	49	- 52	10 -	19	2	97 -99		10 - 19	2
	53	- 56	10 -	19	3
	57	- 60	10 -	19	4
	61	- 64	10 -	19	5	How to Use These Tables
	65	- 68	10 -	19	6
						Read accross from left to right. For the 1st
	69	- 72	10 -	19	7
						module’s addressing sequence (products
	73	- 76	10 -	19	8
						one through four) set the MODULE ID to
	77	- 80	10 -	19	9
						“0 - 9” on the slide switch, and “0” on the
	81	- 84	20 -	29*	0
						rotary switch.
	85	- 88	20 -	29*	1
	89	- 92	20 -	29*	2
	93	- 96	20 -	29*	3
	97	- 99	20 -	29*	4
						* Contact the factory if this address is needed.

16