Audio Authority Car Audio System installation manual Example System, Addressing Low-Level Bus

Page 40

	EXAMPLE SYSTEM 1 •		Addressing	•	Low-Level Bus
	TWO-CHANNEL SYSTEM	•	System Bus	•	Speaker Bus
	TWO-CHANNEL SYSTEM	•	DC Bus	•	Amplifier Bypass
		•	DC Bus	•	Amplifier Bypass

2/77 Power Source

Amplifiers	916X	942
		4/01

903

980

02 910

01 910

System Bus

Speaker Bus

LevelBus	AmplifierBypass
Low-

High Powered Sources

4/00R	RightFrontSpeakers	ADDRESSINGKEY	R4/01 (932only)	MODULEGROUPID
932			RIGHT
			LEFT-
SpeakerBus	SampleSystemCapacity:	8 Sources(2chlow&2chhigh-level) 3 FrontAmplifiers(2chinput&2choutput)	8 SpeakerPairs	ProcessorBypass AmplifierBypass

932	FrontSpeakers	ControlCable SystemBus SpeakerBus Low-LevelBus DCBus 4GaugeBlack 4GaugeRed
4/00L	Left

	ASD Tech Support USA and Canada: 800-322-8346(Mon-Fri 8:30 AM to 5:00 PM Eastern Time)
40	Phone: 859-233-4599 Fax: 859-233-4510 Hookup drawings and FAQ http://www.audioauthority.com

Image 40

Contents Demonstration Network Car Audio Page Contents Introduction What is the Access System? Definition of TermsProduct Select HOW the Access System Works Selecting Products in the Access SystemBuses 922Access System Components Access User InterfacesControl Panels Full-Featured Control Panel Features includeSwitching Modules Expander Modules System ModuleSystem Specific Components DC Distribution Modules Choosing the Correct Switching Modules Product GroupsHead Units 910Amplifier Product Groups Amp SharingAmpifier Bypass SpeakersBegin Installation Address and Other SettingsPreparation Number the Product GroupsDetermine the Module ID settings How to Use These TablesSources, EQs and Amplifiers Speakers Set the Programming Switches Set the Address SwitchesProgramming Switch Settings S M B T D Set the Left-Right Switch Timeout Minutes and ModelSilenTouch and Model Speaker LimitInstalling the System Hardware Designate the Switching Module LocationsDetermine Other Module Locations Mount the ModulesBlue Install Speaker Bus Low-Level BusesEQ and Amplifier Bypass Low-Level Bus Illustration.Low-LevelInstall the DC Power Distribution Cables Choosing the Power Mode for Your Display Power Supply VentilationSetting the Parallel Speaker Limits Install the RF Antenna Distribution System Check Your Work to This PointObserve correct polarity for all bus connections Installing a Control Panel Rear view of the 902 Control PanelControl Panel Expanders Control Panel Cutout SizesInstalling Product Select Buttons and Product Indicators Be careful to maintain PSB Cable polarity at both endsRemote Power Switch System Module AccessoriesTheftAlert Remote System Reset Testing Network Function902 Page Install the First Products Display Component HookupPage Test Your Initial Product Installation Connect the Battery Install the Remaining ProductsTroubleshooting Noise Problems Test Product SelectionSelecting Additional Speaker Pairs with PSBs Deselecting Products with PSBsB System Comparison TheftAlert ProtectionSystem, DC and Signal Bus Wiring Diagrams Product to Switch Module Wiring DiagramsAddressing Low-Level Bus Example SystemSystem Bus Speaker Bus DC Bus Amplifier Bypass System Bus AddressingAmp Bypass EQ Bypass AMP Shared System 942 916X 932 Example of split Model 910D Setup Ch. High-Level 2-Ch Low-Level Head UnitChannel Signal Processor Or Equalizer Power Expander915X DC EQ Bypass NoteChannel Setup for 980EZ Model 980 System Module / 2- and 6-Channel HookupAmplifiers / 2-Channel Hookup Channel Amplifier916X Amp Bypass NoteAmplifiers / 4-Channel Hookup BAT+Shared Amplifier Hookup 942Left/Right and Mono Speaker Hookup Left Speaker RightAccess Warranty Limited WarrantyWarranty Service Procedures Out of Warranty ServiceIndex