Audio Authority Car Audio System Control Panel Expanders, Control Panel Cutout Sizes

Page 29

•Plug the calibration microphone into the Microphone jack located on the rear of the 902, using the extension cable provided, if necessary.

•If your system includes a Model 990 Remote Infrared Receiver, mount the 990 to the ceiling in the display area and connect the 990 to the header on the rear of the 902 labeled “Aux IR.”

Note: The 903 Control Panel can also be remotely controlled using a 905 IR Remote. A single 905 remote is packaged with the 902, but must be ordered separately for the 903.

4.Set the Programming Switches on the 902/903.

•Use the following chart to set the 8 programming switches located on the rear of the 902/903 Control Panels (next page).

Switch

Function

Comments

A

Keyboard Click

Turn ON for audible key feedback or “beep”

B

Demo-Mode

Leave OFF. Use only when control panel is not

 

 

connected to a system as a “Training Mode”

C

Systems

ON makes the last unused Product Groupcapable of

 

Memory

storing and recalling 99 system configurations*

D

Future Use

Spare, leave OFF

E

Previous Selection

OFF = “C” key is third “flash memory” key

 

 

ON = “C” key is toggle between current selection and previous selection

F

902/903

902 = OFF; 903 = ON

G

Internal IR

Turn OFF when using 990 Remote IR Receiver

H

Auxiliary IR

Turn ON when using 990 Remote IR Receiver

*If a 904 or 904V Product Group Expander is installed, the last Product Group on the Expander is used for “Systems” instead of the last Product Group on the 902/903 itself.

Control Panel Expanders.

All panel openings are 51⁄8” (130 mm) high. Correct cutout widths are shown below. If you have a 904 or

904V Control Panel Expander for use with your 902/903, follow these instructions:

•Cut an opening 11-3⁄16” (285 mm) wide by 51⁄8” (130 mm) high to accommodate both the 902/903 and the 904 panels.

•Insert the appropriate slide-in Product Group labels provided with your control panel into the product group display windows.

•Connect the 904 ribbon cable to the matching header on the rear of the 902/903 marked “To 904.”

•Mount the Expander in the opening together with the 902/903 Control Panel.

Control Panel Cutout Sizes

Panel Units

Cutout Width

906 or 988CP0

41⁄16” (105 mm)

902 or 903

7” (178 mm)

902/3 + one expander

113⁄16” (285 mm)

902/3 + two expanders

153⁄8” (390 mm)

902/3 + three expanders

199⁄16” (495 mm)

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Demonstration Network Car Audio Page Contents Introduction Definition of Terms What is the Access System?Product Select Selecting Products in the Access System HOW the Access System WorksBuses 922Access User Interfaces Access System ComponentsControl Panels Full-Featured Control Panel Features includeSwitching Modules System Specific Components System ModuleExpander Modules DC Distribution Modules Product Groups Choosing the Correct Switching ModulesHead Units 910Amp Sharing Amplifier Product GroupsSpeakers Ampifier BypassAddress and Other Settings Begin InstallationPreparation Number the Product GroupsSources, EQs and Amplifiers Speakers How to Use These TablesDetermine the Module ID settings Programming Switch Settings S M B T D Set the Address SwitchesSet the Programming Switches Timeout Minutes and Model Set the Left-Right SwitchSilenTouch and Model Speaker LimitDesignate the Switching Module Locations Installing the System HardwareDetermine Other Module Locations Mount the ModulesBlue Low-Level Buses Install Speaker BusLow-Level Bus Illustration.Low-Level EQ and Amplifier BypassInstall the DC Power Distribution Cables Power Supply Ventilation Choosing the Power Mode for Your DisplaySetting the Parallel Speaker Limits Check Your Work to This Point Install the RF Antenna Distribution SystemObserve correct polarity for all bus connections Rear view of the 902 Control Panel Installing a Control PanelControl Panel Cutout Sizes Control Panel ExpandersBe careful to maintain PSB Cable polarity at both ends Installing Product Select Buttons and Product IndicatorsTheftAlert System Module AccessoriesRemote Power Switch 902 Testing Network FunctionRemote System Reset Page Display Component Hookup Install the First ProductsPage Test Your Initial Product Installation Install the Remaining Products Connect the BatteryTroubleshooting Noise Problems Test Product SelectionDeselecting Products with PSBs Selecting Additional Speaker Pairs with PSBsB System Comparison TheftAlert ProtectionProduct to Switch Module Wiring Diagrams System, DC and Signal Bus Wiring DiagramsSystem Bus Speaker Bus DC Bus Amplifier Bypass Example SystemAddressing Low-Level Bus Addressing System BusAmp Bypass EQ Bypass AMP Shared System 942 916X 932 Ch. High-Level 2-Ch Low-Level Head Unit Example of split Model 910D SetupPower Expander Channel Signal Processor Or Equalizer915X DC EQ Bypass NoteModel 980 System Module / 2- and 6-Channel Hookup Channel Setup for 980EZChannel Amplifier Amplifiers / 2-Channel Hookup916X Amp Bypass NoteBAT+ Amplifiers / 4-Channel Hookup942 Shared Amplifier HookupLeft Speaker Right Left/Right and Mono Speaker HookupLimited Warranty Access WarrantyWarranty Service Procedures Out of Warranty ServiceIndex
Top Page Image Contents