Audio Authority Car Audio System installation manual System Bus, Addressing

Page 41

	EXAMPLE SYSTEM 2 •		System Bus
	SIX-CHANNEL SYSTEM	•	DC Bus
	SIX-CHANNEL SYSTEM	•	Addressing
		•	Addressing

2/77 Power Source

	916X	942
Amps		4/01
Front	916X	942
		4/00
	SystemBus	980

Battery	4/00R	932
Car	4/01R	932

Rear	Amps
916X	942	916X
	5/00
		Switching SystemPower

Speakers	5/00R
RightFront	5/01R

Sub Amps 942 6/00

932 932

Speakers	6/00R
RightRear	6/01R

932 932

ADDRESSING KEY

Right Sub Speakers

RIGHT	only)
LEFT-	(932	GROUP MODULEID
4/01R	(932	GROUP MODULEID

High Powered Sources

Preamp EQs	915X	958
		2/00

02 910

01

910

00 910

4/00 L 4/01 L

932 932

System Capacity:

Left Front Speakers

12 High-powered Sources

5/00 L 5/01 L

3 Crossovers/Preamp EQs 7 Front Amplifiers

932 932

3 RearAmplifiers 4 SubAmplifiers 16 FrontSpeakerPairs 16 RearSpeakerPairs 16 SubSpeakerPairs

ProcessorBypass AmplifierBypass

Speakers	6/01L
LeftRear	6/00L

932 932

System Bus yellow/blue/red/black DC Bus 14 gauge red/black 4 gauge black 4 gauge red

Left Sub Speakers

ASD Tech Support USA and Canada: 800-322-8346(Mon-Fri 8:30 AM to 5:00 PM Eastern Time)
Phone: 859-233-4599 Fax: 859-233-4510 Hookup drawings and FAQ http://www.audioauthority.com	41

Image 41

Contents Demonstration Network Car Audio Page Contents Introduction Definition of Terms What is the Access System?Product Select Selecting Products in the Access System HOW the Access System WorksBuses 922Access User Interfaces Access System ComponentsControl Panels Full-Featured Control Panel Features includeSwitching Modules System Specific Components System ModuleExpander Modules DC Distribution Modules Product Groups Choosing the Correct Switching ModulesHead Units 910Amp Sharing Amplifier Product GroupsSpeakers Ampifier BypassAddress and Other Settings Begin InstallationPreparation Number the Product GroupsSources, EQs and Amplifiers Speakers How to Use These TablesDetermine the Module ID settings Programming Switch Settings S M B T D Set the Address SwitchesSet the Programming Switches Timeout Minutes and Model Set the Left-Right SwitchSilenTouch and Model Speaker LimitDesignate the Switching Module Locations Installing the System HardwareDetermine Other Module Locations Mount the ModulesBlue Low-Level Buses Install Speaker BusLow-Level Bus Illustration.Low-Level EQ and Amplifier BypassInstall the DC Power Distribution Cables Power Supply Ventilation Choosing the Power Mode for Your DisplaySetting the Parallel Speaker Limits Check Your Work to This Point Install the RF Antenna Distribution SystemObserve correct polarity for all bus connections Rear view of the 902 Control Panel Installing a Control PanelControl Panel Cutout Sizes Control Panel ExpandersBe careful to maintain PSB Cable polarity at both ends Installing Product Select Buttons and Product IndicatorsTheftAlert System Module AccessoriesRemote Power Switch 902 Testing Network FunctionRemote System Reset Page Display Component Hookup Install the First ProductsPage Test Your Initial Product Installation Install the Remaining Products Connect the BatteryTroubleshooting Noise Problems Test Product SelectionDeselecting Products with PSBs Selecting Additional Speaker Pairs with PSBsB System Comparison TheftAlert ProtectionProduct to Switch Module Wiring Diagrams System, DC and Signal Bus Wiring DiagramsSystem Bus Speaker Bus DC Bus Amplifier Bypass Example SystemAddressing Low-Level Bus Addressing System BusAmp Bypass EQ Bypass AMP Shared System 942 916X 932 Ch. High-Level 2-Ch Low-Level Head Unit Example of split Model 910D SetupPower Expander Channel Signal Processor Or Equalizer915X DC EQ Bypass NoteModel 980 System Module / 2- and 6-Channel Hookup Channel Setup for 980EZChannel Amplifier Amplifiers / 2-Channel Hookup916X Amp Bypass NoteBAT+ Amplifiers / 4-Channel Hookup942 Shared Amplifier HookupLeft Speaker Right Left/Right and Mono Speaker HookupLimited Warranty Access WarrantyWarranty Service Procedures Out of Warranty ServiceIndex