Audio Authority Car Audio System Access Warranty, Limited Warranty, Warranty Service Procedures

Page 52

ACCESSWARRANTY

Limited Warranty

Should any Accessproduct become defective in materials or workmanship within 5 years from the date of purchase, Audio Authority® Corporation guarantees to the original purchaser that it will replace the defec- tive product at no cost. This warranty is not applicable for products which, in our opinion, have been damaged, altered, abused, misused, or improperly installed.

Warranty Service Procedures

If you suspect a product defect, contact the Audio Authority® Technical Service Department by calling 800/322-8346 or 859/233-4599 for assistance in verifying the problem. If a defect is found, a replacement product will be shipped immediately, prepaid via UPS or FedEx Ground, on a defect-exchange basis and a Return Authorization number will be issued for the defective product. At the time of shipment, the replace- ment product is invoiced to the customer, secured via a bank card, and later credited in full upon inspection of the defective product. A bank card sales draft is executed for the cost of the replacement product and held for 14 days to allow the customer time to return the defective product. If the defective product is not re- ceived within 14 days, the bank card sales draft is deposited. All returns for credit must be freight prepaid.

Alternatively, if the customer has previously established open account terms, the invoice amount can be charged to his account and later cleared with a corresponding credit memo upon receipt and inspection of the defective product. Similarly, the defect-exchange transaction may be handled by COD, in which case Audio Authority® will issue a refund check upon inspection of the defective return.

Alternate methods of return shipping (UPS Red, Federal Express, DHL, etc.) are available, but at the customer’s expense.

Defects Within the First 30 Days

Replacements for products found defective within the first 30 days from date of sale, will be shipped via overnight courier, freight paid by Audio Authority.®

Out of Warranty Service

Products not within the terms of the AccessWarranty may be returned to our factory, freight prepaid, for repair at a labor rate of $35/hour (1 hour minimum) plus parts and return freight. Repairs are normally shipped within 2 working days via UPS or FedEx Ground unless requested otherwise. Payment for repairs is made via bank card or COD unless other arrangements are requested and approved.

Alternatively, out-of-warranty repairs may be accomplished on a defect exchange basis. The customer will be invoiced, per the terms above, at the current dealer cost for the replacement product. When the defective product is returned and inspected, a partial refund or credit will be issued based on its condition and the repair costs.

For future reference, please record below:

Date of Purchase: ___/___/___

Invoice No: __________________

52

Image 52
Contents Demonstration Network Car Audio Page Contents Introduction What is the Access System? Definition of TermsProduct Select HOW the Access System Works Selecting Products in the Access SystemBuses 922Access System Components Access User InterfacesControl Panels Full-Featured Control Panel Features includeSwitching Modules Expander Modules System ModuleSystem Specific Components DC Distribution Modules Choosing the Correct Switching Modules Product GroupsHead Units 910Amplifier Product Groups Amp SharingAmpifier Bypass SpeakersBegin Installation Address and Other SettingsPreparation Number the Product GroupsDetermine the Module ID settings How to Use These TablesSources, EQs and Amplifiers Speakers Set the Programming Switches Set the Address SwitchesProgramming Switch Settings S M B T D Set the Left-Right Switch Timeout Minutes and ModelSilenTouch and Model Speaker LimitInstalling the System Hardware Designate the Switching Module LocationsDetermine Other Module Locations Mount the ModulesBlue Install Speaker Bus Low-Level BusesEQ and Amplifier Bypass Low-Level Bus Illustration.Low-LevelInstall the DC Power Distribution Cables Choosing the Power Mode for Your Display Power Supply VentilationSetting the Parallel Speaker Limits Install the RF Antenna Distribution System Check Your Work to This PointObserve correct polarity for all bus connections Installing a Control Panel Rear view of the 902 Control PanelControl Panel Expanders Control Panel Cutout SizesInstalling Product Select Buttons and Product Indicators Be careful to maintain PSB Cable polarity at both endsRemote Power Switch System Module AccessoriesTheftAlert Remote System Reset Testing Network Function902 Page Install the First Products Display Component HookupPage Test Your Initial Product Installation Connect the Battery Install the Remaining ProductsTroubleshooting Noise Problems Test Product SelectionSelecting Additional Speaker Pairs with PSBs Deselecting Products with PSBsB System Comparison TheftAlert ProtectionSystem, DC and Signal Bus Wiring Diagrams Product to Switch Module Wiring DiagramsAddressing Low-Level Bus Example SystemSystem Bus Speaker Bus DC Bus Amplifier Bypass System Bus AddressingAmp Bypass EQ Bypass AMP Shared System 942 916X 932 Example of split Model 910D Setup Ch. High-Level 2-Ch Low-Level Head UnitChannel Signal Processor Or Equalizer Power Expander915X DC EQ Bypass NoteChannel Setup for 980EZ Model 980 System Module / 2- and 6-Channel HookupAmplifiers / 2-Channel Hookup Channel Amplifier916X Amp Bypass NoteAmplifiers / 4-Channel Hookup BAT+Shared Amplifier Hookup 942Left/Right and Mono Speaker Hookup Left Speaker RightAccess Warranty Limited WarrantyWarranty Service Procedures Out of Warranty ServiceIndex