Audio Authority Car Audio System installation manual AMP Shared System

Page 43

	EXAMPLE SYSTEM 3 •		System Bus
	AMP SHARED SYSTEM	•	DC Bus
	AMP SHARED SYSTEM	•	Addressing
		•	Addressing

Model993AmpShareAdaptor	instructions,seepage50.
For

2/77 Power Source

942 4/00

Car Battery

Front Amps

916X	942
	5/00

932 932

Rear Amps

4/00R	Speakers
4/01R	RightFront

942 6/00

932 932

Sub Amps

5/00R	Speakers
5/01R	RightRear

932 932

	RIGHT-LEFT	GROUP MODULEID
ADDRESSINGKEY	4/01R only)(932	GROUP MODULEID

6/00R	Speakers
6/01R	RightSub

903

System Bus

02

01

00

980

915X	958
	2/01
915X	958
	2/00

910 910 910

Preamp EQs

SourcesPowered

High

932 932

4/01L	Speakers
4/00L	LeftFront

932 932

Sample System Capacity:

5/00 L 5/01 L

High-poweredSources	Crossovers/PreampEQs	SharedAmplifiers(anyposition)	FrontSpeakerPairs	RearSpeakerPairs	SubSpeakerPairs
12	7	3	16	16	16

ControlCable	SystemBus DCBus ExpansionCable
	DC
Speakers	932
LeftRear	932

ProcessorBypass

AmplifierBypass

GaugeBlack	4GaugeRed
4

6/01L	Speakers
6/00L	LeftSub

ASD Tech Support USA and Canada: 800-322-8346(Mon-Fri 8:30 AM to 5:00 PM Eastern Time)
Phone: 859-233-4599 Fax: 859-233-4510 Hookup drawings and FAQ http://www.audioauthority.com	43

Image 43

Contents Demonstration Network Car Audio Page Contents Introduction Definition of Terms What is the Access System?Product Select 922 HOW the Access System WorksSelecting Products in the Access System BusesFeatures include Access System ComponentsAccess User Interfaces Control Panels Full-Featured Control PanelSwitching Modules Expander Modules System ModuleSystem Specific Components DC Distribution Modules 910 Choosing the Correct Switching ModulesProduct Groups Head UnitsAmp Sharing Amplifier Product GroupsSpeakers Ampifier BypassNumber the Product Groups Begin InstallationAddress and Other Settings PreparationDetermine the Module ID settings How to Use These TablesSources, EQs and Amplifiers Speakers Set the Programming Switches Set the Address SwitchesProgramming Switch Settings S M B T D Speaker Limit Set the Left-Right SwitchTimeout Minutes and Model SilenTouch and ModelMount the Modules Installing the System HardwareDesignate the Switching Module Locations Determine Other Module LocationsBlue Low-Level Buses Install Speaker BusLow-Level Bus Illustration.Low-Level EQ and Amplifier BypassInstall the DC Power Distribution Cables Power Supply Ventilation Choosing the Power Mode for Your DisplaySetting the Parallel Speaker Limits Check Your Work to This Point Install the RF Antenna Distribution SystemObserve correct polarity for all bus connections Rear view of the 902 Control Panel Installing a Control PanelControl Panel Cutout Sizes Control Panel ExpandersBe careful to maintain PSB Cable polarity at both ends Installing Product Select Buttons and Product IndicatorsRemote Power Switch System Module AccessoriesTheftAlert Remote System Reset Testing Network Function902 Page Display Component Hookup Install the First ProductsPage Test Your Initial Product Installation Test Product Selection Connect the BatteryInstall the Remaining Products Troubleshooting Noise ProblemsTheftAlert Protection Selecting Additional Speaker Pairs with PSBsDeselecting Products with PSBs B System ComparisonProduct to Switch Module Wiring Diagrams System, DC and Signal Bus Wiring DiagramsAddressing Low-Level Bus Example SystemSystem Bus Speaker Bus DC Bus Amplifier Bypass Addressing System BusAmp Bypass EQ Bypass AMP Shared System 942 916X 932 Ch. High-Level 2-Ch Low-Level Head Unit Example of split Model 910D SetupEQ Bypass Note Channel Signal Processor Or EqualizerPower Expander 915X DCModel 980 System Module / 2- and 6-Channel Hookup Channel Setup for 980EZAmp Bypass Note Amplifiers / 2-Channel HookupChannel Amplifier 916XBAT+ Amplifiers / 4-Channel Hookup942 Shared Amplifier HookupLeft Speaker Right Left/Right and Mono Speaker HookupOut of Warranty Service Access WarrantyLimited Warranty Warranty Service ProceduresIndex