Audio Authority Car Audio System installation manual Test Your Initial Product Installation

Page 36

•Connect the left speaker to one of the 2 position terminal blocks on the Left 932 and the right speaker to the corresponding position on the Right 932. Wire the positive lead to (+) and the negative speaker lead to (–).

•Connect the two-pin plug of the PSB’s cable, if PSBs are used, to the small 2 pin headers on the 932 circuit board at the corresponding product position. Press the PSB into the 3⁄4” hole you drilled earlier in the mounting panel or display fixture.

Note: One PSB will activate both left and right speakers when selected. You may also wish to install a 996 or 997 Product Indicator at the alternate speaker location for easy product selection verification. Product Indicators are merely LEDs; they connect to any switching module in exactly the same manner as PSBs (see pp. 9, 30).

•Install the speakers in the display fixture. Tightly seal all speaker chambers, especially subwoofer enclosures.

2.Test Your Initial Product Installation

A.Use PSBs or the Control Panel, depending on how your system is equipped.

•On a 902 or 903, press the first key at the top of the column of 8 Product Group keys. The red LED comes on.

•Enter the number of the first product in the Source Group using the numeric pad. The Product Group Display blinks while receiving your input.

•The Product Group Display stops blinking after two seconds and the selected product comes on.

•Enter the numbers of the remaining test products in their respective Product Groups.

B.Adjust the product controls until you hear music. If none is heard:

•Check for source material (cassette, CD, FM tuning).

•Check your product selection numbers on the control panel for accuracy.

•Check product connections to the switching modules.

•Make sure all products are receiving DC power.

•Check all Group, Module, and programming switch settings. Refer to the configuration on the information boxes and your system plan.

Note: If you make any changes to any module’s switch settings, press the System Reset button on the 980 System Module. In systems with control panels, you can also press “Secure, 88, Secure” on the control panel to reset the system. This enables the modules to recognize the new settings.

•Make sure that PSBs, if present, are connected to the correct header position.

•If PSBs are not installed, plug the test PSB that came with the 980 System Module into the respec- tive headers on the switching modules to make sure that the products are currently selected to play.

•Follow the signal path visually through the product hookups and system buses to make sure there are no wiring errors.

•If you are still experiencing difficulties, call Audio Authority’s Technical Service at 800/322-8346.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Demonstration Network Car Audio Page Contents Introduction What is the Access System? Definition of TermsProduct Select HOW the Access System Works Selecting Products in the Access SystemBuses 922Access System Components Access User InterfacesControl Panels Full-Featured Control Panel Features includeSwitching Modules System Module Expander ModulesSystem Specific Components DC Distribution Modules Choosing the Correct Switching Modules Product GroupsHead Units 910Amplifier Product Groups Amp SharingAmpifier Bypass SpeakersBegin Installation Address and Other SettingsPreparation Number the Product GroupsHow to Use These Tables Determine the Module ID settingsSources, EQs and Amplifiers Speakers Set the Address Switches Set the Programming SwitchesProgramming Switch Settings S M B T D Set the Left-Right Switch Timeout Minutes and ModelSilenTouch and Model Speaker LimitInstalling the System Hardware Designate the Switching Module LocationsDetermine Other Module Locations Mount the ModulesBlue Install Speaker Bus Low-Level BusesEQ and Amplifier Bypass Low-Level Bus Illustration.Low-LevelInstall the DC Power Distribution Cables Choosing the Power Mode for Your Display Power Supply VentilationSetting the Parallel Speaker Limits Install the RF Antenna Distribution System Check Your Work to This PointObserve correct polarity for all bus connections Installing a Control Panel Rear view of the 902 Control PanelControl Panel Expanders Control Panel Cutout SizesInstalling Product Select Buttons and Product Indicators Be careful to maintain PSB Cable polarity at both endsSystem Module Accessories Remote Power SwitchTheftAlert Testing Network Function Remote System Reset902 Page Install the First Products Display Component HookupPage Test Your Initial Product Installation Connect the Battery Install the Remaining ProductsTroubleshooting Noise Problems Test Product SelectionSelecting Additional Speaker Pairs with PSBs Deselecting Products with PSBsB System Comparison TheftAlert ProtectionSystem, DC and Signal Bus Wiring Diagrams Product to Switch Module Wiring DiagramsExample System Addressing Low-Level BusSystem Bus Speaker Bus DC Bus Amplifier Bypass System Bus AddressingAmp Bypass EQ Bypass AMP Shared System 942 916X 932 Example of split Model 910D Setup Ch. High-Level 2-Ch Low-Level Head UnitChannel Signal Processor Or Equalizer Power Expander915X DC EQ Bypass NoteChannel Setup for 980EZ Model 980 System Module / 2- and 6-Channel HookupAmplifiers / 2-Channel Hookup Channel Amplifier916X Amp Bypass NoteAmplifiers / 4-Channel Hookup BAT+Shared Amplifier Hookup 942Left/Right and Mono Speaker Hookup Left Speaker RightAccess Warranty Limited WarrantyWarranty Service Procedures Out of Warranty ServiceIndex
Top Page Image Contents