Audio Authority Car Audio System installation manual Shared Amplifier Hookup, 942

Page 50

Shared Amplifier Hookup

This diagram shows one stereo amplifier connected to all three Amplifier Product Groups so that it can play in the front, rear, or sub position. To add three more shared amplifiers, connect each to its own Model 993 adapter, and then connect the adapter to corresponding positions on each 942 module. If some of your amps will be shared, and some not shared, contact Audio Authority® at the phone number below for assistance.

First, mount the switching modules inside your display according to your system plan. Then use the screws provided to mount each amp’s 993 adapter inside the cabinet or on the back of the amplifier display panel near the amplifier to be shared. Connect the Input and Output cables from each 942 module to the 993 adapter as shown. Connect the amplifier to the adapter using the “SHARED AMP” terminals and jacks on the 993. Contact Audio Authority® Technical Service at the phone number below with questions.

Connect Amplifier’s DC

Amplifier

power to a 916X

expander on any of its

associated 942 modules

Low-Level Input

Front Amp Position

Rear Amp Position

Sub Amp Position

Low-Level Inputs

Low-Level Inputs

Low-Level Inputs

(see pp. 22, 43).

Model 993 Amp

Share Adapter

(mount this adapter inside the display near the shared amp)

Screw Terminal

Speaker-Level Output

993

FRONT 942

L+ L– R+ R–

REAR 942

SUB 942

SHARED AMP

S

Mounting

Screws

Left Right

DC Power

Shared Amplifier

Position #4

High-Level

Output

942

Front Amp Position

942

Switch Module

Rear Amp Position

942

 

Switch Module

 

Sub Amp Position

Switch Module

Amplifier

 

Speaker-Level Output

S

 

 

S

 

S

See Appendix A for other system related connections such as System Bus, DC distribution, or Low-Level and High-Level Bus.

 

Note: This drawing is not to scale.

50

ASD Tech Support USA and Canada: 800-322-8346(Mon-Fri 8:30 AM to 5:00 PM Eastern Time)

Phone: 859-233-4599 Fax: 859-233-4510 Hookup drawings and FAQ http://www.audioauthority.com

Image 50
Contents Demonstration Network Car Audio Page Contents Introduction What is the Access System? Definition of TermsProduct Select Buses HOW the Access System WorksSelecting Products in the Access System 922Control Panels Full-Featured Control Panel Access System ComponentsAccess User Interfaces Features includeSwitching Modules System Specific Components System ModuleExpander Modules DC Distribution Modules Head Units Choosing the Correct Switching ModulesProduct Groups 910Amplifier Product Groups Amp SharingAmpifier Bypass SpeakersPreparation Begin InstallationAddress and Other Settings Number the Product GroupsSources, EQs and Amplifiers Speakers How to Use These TablesDetermine the Module ID settings Programming Switch Settings S M B T D Set the Address SwitchesSet the Programming Switches SilenTouch and Model Set the Left-Right SwitchTimeout Minutes and Model Speaker LimitDetermine Other Module Locations Installing the System HardwareDesignate the Switching Module Locations Mount the ModulesBlue Install Speaker Bus Low-Level BusesEQ and Amplifier Bypass Low-Level Bus Illustration.Low-LevelInstall the DC Power Distribution Cables Choosing the Power Mode for Your Display Power Supply VentilationSetting the Parallel Speaker Limits Install the RF Antenna Distribution System Check Your Work to This PointObserve correct polarity for all bus connections Installing a Control Panel Rear view of the 902 Control PanelControl Panel Expanders Control Panel Cutout SizesInstalling Product Select Buttons and Product Indicators Be careful to maintain PSB Cable polarity at both endsTheftAlert System Module AccessoriesRemote Power Switch 902 Testing Network FunctionRemote System Reset Page Install the First Products Display Component HookupPage Test Your Initial Product Installation Troubleshooting Noise Problems Connect the BatteryInstall the Remaining Products Test Product SelectionB System Comparison Selecting Additional Speaker Pairs with PSBsDeselecting Products with PSBs TheftAlert ProtectionSystem, DC and Signal Bus Wiring Diagrams Product to Switch Module Wiring DiagramsSystem Bus Speaker Bus DC Bus Amplifier Bypass Example SystemAddressing Low-Level Bus System Bus AddressingAmp Bypass EQ Bypass AMP Shared System 942 916X 932 Example of split Model 910D Setup Ch. High-Level 2-Ch Low-Level Head Unit915X DC Channel Signal Processor Or EqualizerPower Expander EQ Bypass NoteChannel Setup for 980EZ Model 980 System Module / 2- and 6-Channel Hookup916X Amplifiers / 2-Channel HookupChannel Amplifier Amp Bypass NoteAmplifiers / 4-Channel Hookup BAT+Shared Amplifier Hookup 942Left/Right and Mono Speaker Hookup Left Speaker RightWarranty Service Procedures Access WarrantyLimited Warranty Out of Warranty ServiceIndex