Alpine CDA-9813, CDA-9811, CDA-9815 owner manual Installation and Connections, 34-EN

Page 36

Installation and Connections

Before installing or connecting the unit, please read the following and pages 3 to 5 of this manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury.

If swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.

Precautions

Be sure to disconnect the cable from the (–) battery post before installing your CDA-9815/CDA-9813/CDA-9811. This will reduce any chance of damage to the unit in case of a short- circuit.

Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle's electrical system.

When making connections to the vehicle's electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the CDA-9815/CDA-9813/CDA- 9811 to the fuse box, make sure the fuse for the intended circuit of the CDA-9815/CDA-9813/CDA-9811 has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer.

The CDA-9815/CDA-9813/CDA-9811 uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized ALPINE dealer for assistance.

Be sure to connect the speaker (–) leads to the speaker (–) terminal. Never connect left and right channel speaker cables to each other or to the vehicle body.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit.

SERIAL NUMBER:

INSTALLATION DATE:

INSTALLATION TECHNICIAN: PLACE OF PURCHASE:

34-EN

Image 36
Contents CDA-9815 CDA-9813 CDA-9811 CHA-S634 CHA-1214CHM-S630Contents Installation and Connections Operating Instructions Never Attempt the Following On handling Compact Discs CD/CD-R/CD-RW Alphanumeric DisplayGetting Started Adjusting Volume Lowering Volume QuicklyChanging the Audio Level Display Pattern Detaching and Attaching the Front PanelRadio CD / MP3 / WMA Station Title Search FunctionQuick Search Function PlaybackPress 5 in the play or pause mode Repeat PlayX. Random Play 10-ENFile Search mode Folder Search modeScanning Programs Quick SearchTerminology 12-ENSound Setting Setting the Bass Control CDA-9811 onlySetting the Treble Control CDA-9811 only Press Rotary encoder repeatedly to choose the desired modeSetting the Bass Type CDA-9811 only Adjusting the built-in Crossover CDA-9811 only14-EN 15-EN WAY System 16-ENAbout Time Correction Example 1. Listening Position Front Left SeatExample 2. Listening Position All Seats 17-ENExample setting for steps 2 Press T.CORR/X-OVER to select the Bass Focus modeBass Focus 18-ENSetting the MX Mode Press BAND/TEL. to select a speaker to be adjustedPress Rotary encoder to return to normal mode 19-ENOther Functions Displaying the Title/Text20-EN Press TitleBlackout Mode On and Off Titling Discs/StationsErasing Disc Title/Station Title Displaying TimePersonalize About i-PersonalizeData Downloading 22-ENSound Customizing Visual Customizing23-EN External Device 24-ENStoring XM Channel Presets XM Radio OptionalReceiving XM Channels with the XM Receiver Optional Checking the XM Radio ID NumberSetting the tuning method Setting the Auxiliary Data Field DisplayChannel/Category Search Function Changing the DisplayTelephone Mode ON/OFF MobileHub Link OperationOptionalAbout MobileHub Link Incoming CallsSMS Short Message Service Operation Press Search in Phone Book mode to select the History modeReceiving a short message Changer Optional Playing MP3 Files with the CD Changer OptionalControlling CD Changer Optional Multi-Changer Selection OptionalRemote Control Controls on Remote ControlOperating the Audio Processor 30-ENBattery Replacement InformationCase of Difficulty BasicIndication for CD Player Indication for CD Changer32-EN Specifications Indication for XM Radio Mode33-EN CDA-9815/CDA-9813CDA-9811Installation and Connections 34-ENInstallation 35-ENSlide the mounting sleeve into the dashboard Connections for CDA-9811 36-EN37-EN To prevent noise/interference in the audio systemConnections for CDA-9815/CDA-9813 38-EN39-EN Audio Interrupt In Lead Pink/Black Illumination Lead OrangePage Limited Warranty ALPINE-1