Alpine CDA-9853R, CDA-9855R Adjusting and Storing the Crossover Settings, WAY System, 20-EN

Page 21

Adjusting and Storing the Crossover Settings

Before performing the following procedures, refer to “About the Crossover” (Page 19).

1 Press and hold MENU for at least 2 seconds.

2 Select the Crossover (X-OVER) mode by sliding your finger on the GlideTouch bar to the left or right. Press the GlideTouch bar under the Crossover (X-OVER) mode.

2 WAY System

3 Press BAND to select the band to be adjusted.

LOW → MID → HIGH → LOW

(SUBW) (REAR) (FRONT) (SUBW)

4 Select the desired cut-off frequency (Crossover Point) by sliding your finger on the GlideTouch bar to the left or right.

Adjustable frequency bands: 20Hz to 200Hz

(in 1/3 octave steps)

5 Press SOURCE/POWER to adjust the slope.

Adjustable slope: 0 (FLAT), 1 (6dB/oct.), 2 (12dB/oct.) 3 (18dB/oct.) 4 (24dB/oct.)

6 Adjust the output level by turning the Rotary encoder.

Adjustable output level: -12 to 0 dB.

7 To adjust another band, repeat steps 3 to 6, then adjust all bands.

8 When the setting has been completed, press FUNC. or the GlideTouch bar to activate the preset mode.

9 Select any one of the preset numbers (1 through 6) by sliding your finger on the GlideTouch bar to the left or right. Press and hold the GlideTouch bar under the desired preset for at least 2 seconds to store the adjusted contents.

10After setting, press and hold MENU for at least 2 seconds to return to normal mode.

•If MENU is pressed while adjusting or setting items in the MENU mode, the unit will return to the previous selection screen.

•By pressing the GlideTouch bar under RETURN in the MENU mode, the unit returns to the normal mode.

•If no operation is performed for 60 seconds, the unit returns to normal mode.

3 WAY System

3 Press BAND to select the band to be adjusted.

LOW → MID-L → MID-H → HIGH → LOW

4 Select the desired cut-off frequency (Crossover Point) by sliding your finger on the GlideTouch bar to the left or right.

Adjustable frequency bands:

LOW: 20Hz to 200Hz (in 1/3 octave steps)

MID-L: 20Hz to 200Hz (in 1/3 octave steps)

MID-H: 20Hz to 20kHz (in 1/3 octave steps)

HIGH: 1kHz to 20 kHz (in 1/3 octave steps)

5 Press SOURCE/POWER to adjust the slope.

Adjustable slope: 0 (FLAT)*, 1 (6dB/oct.), 2 (12dB/oct.) 3 (18dB/oct.) 4 (24dB/oct.)

*FLAT can be set for the HIGH slope only when USER'S is selected in “Setting the Response Slope for the High Range Speaker (TW SETUP)” (page 31). Depending on the response characteristics of the speaker, care should be taken when setting the response slope to FLAT, as speaker damage may result. With the CDA-9855R, a message is displayed when the response slope for the high range speaker is set to FLAT.

6 Adjust the output level by turning the Rotary encoder.

Adjustable output level: -12 to 0 dB.

7 To adjust another band, repeat steps 3 to 6, then adjust all bands.

8 When the setting has been completed, press FUNC. or the GlideTouch bar to activate the preset mode.

9 Select any one of the preset numbers (1 through 6) by sliding your finger on the GlideTouch bar to the left or right. Press and hold the GlideTouch bar under the desired preset for at least 2 seconds to store the adjusted contents.

10After setting, press and hold MENU for at least 2 seconds to return to normal mode.

•If MENU is pressed while adjusting or setting items in the MENU mode, the unit will return to the previous selection screen.

•By pressing the GlideTouch bar under RETURN in the MENU mode, the unit returns to the normal mode.

•If no operation is performed for 60 seconds, the unit returns to normal mode.

•About the 2way/3way system

You can switch to 2way/3way system mode with the 2way/3way switch on the bottom side of the unit (pages 42 to 44).

When setting to “3 WAY”:

F/R Sub-W

The unit can be operated in a 3 way system.

3WAY

When setting to “F/R/Sub-W”:

The unit can be operated in a 2 way system.

20-EN

Page 20 Page 22
Image 21
Page 20 Page 22
Contents CDA-9855R DE CDA-9853R Contents Installation and Connections Operating Instructions Never Attempt the Following On handling Compact Discs CD/CD-R/CD-RW About the GlideTouch Bar Operation Touch or press the desired position on the GlideTouch barMove your finger on the GlideTouch bar to the left or right Getting Started Radio Press TUNE/A.ME to select the tuning modeDetaching and Attaching the Front Panel Listening to RadioAutomatic Memory of Station Presets Manual Storing of Station PresetsTuning to Preset Stations Station Title Search FunctionRecalling Preset RDS Stations Setting RDS Reception Mode and Receiving RDS StationsPress FUNC. to activate the audio function mode Receiving RDS Regional Local StationsPTY Programme Type Tuning PI Seek SettingReceiving Traffic Information Receiving Traffic Information While Playing CD or RadioDisplaying Radio Text Priority PTY Programme Type12-EN GlideTouch bar under P.PTY13-EN PlaybackX. Random Play Repeat PlayScanning Programmes 14-ENFile/Folder Name Search concerning MP3/ WMA Searching from CD TextQuick Search About MP3/WMA16-EN TerminologyEqualizer Presets Sound SettingSetting Users EQ mode 17-ENAdjusting and Storing the Graphic Equalizer Curve Adjusting and Storing the Parametric Equalizer CurveAdjust the level by turning the Rotary encoder Press SOURCE/POWER to set the band width QRecalling the Stored Equalizer Curve Way modeAbout the Crossover 19-ENPress SOURCE/POWER to adjust the slope Adjusting and Storing the Crossover SettingsAdjust the output level by turning the Rotary encoder WAY SystemAbout Time Correction Recalling the Stored Crossover SettingsExample 1. Listening Position Front Left Seat Example 2. Listening Position All SeatsAdjusting and Storing the Time Correction Setting the Time Correction UnitDisplay Setup menu is displayed 22-ENSetting the MX Mode Recalling the Stored Time Correction SettingsAbout the MX indicator display CDA-9853R only 23-ENDisplaying the Title/Text Other Functions24-EN Press Title25-EN Titling Discs/StationsAbout Title and Text Press Title and select the Title DisplayErasing Disc Title/Station Title Setting Amplifier LinkIf a Mono Amplifier is Connected If a 4ch Amplifier is ConnectedChanging the Lighting Colour of All the Buttons Setting the Multicolour IlluminationIf you want to use colours other than the above 27-ENData Downloading About i-Personalize28-EN File name of download data shall be AU*****.MP3Playing MP3/WMA Data Play Mode General SettingSetup menu of the selected item is displayed 29-EN30-EN Tuner SettingAudio Setting Display Setting31-EN Demo Setting Searching for a desired Song32-EN Searching by artist name Searching by PlaylistSearching by album name 33-ENRandom Play Shuffle M.I.X Displaying the Text34-EN Controlling CD Changer Optional Changer OptionalPlaying MP3 Files with the CD Changer Optional Multi-Changer Selection Optional36-EN Remote ControlInformation Battery Replacement CDA-9855R onlyCase of Difficulty BasicIndication for CD Player AudioIndication for CD Changer 38-ENIndication for iPod Mode Specifications39-EN Bottom side of player40-EN Installation and ConnectionsInstallation 41-ENRemoval 42-EN Connections43-EN Amplifier Link / Vehicle Display Interface ConnectorTo prevent noise/interference in the audio system 44-ENCHM-S630 CHA-S634 CHA-1214 Alpine CD Changers Give You MoreAppendix Q9 no
Top Page Image Contents