Alpine CDA-9853R, CDA-9855R owner manual Installation and Connections, 40-EN

Page 41

Installation and Connections

Before installing or connecting the unit, please read the following and pages 3 to 5 of this manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury.

If swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.

Precautions

•Be sure to disconnect the cable from the (–) battery post before installing your CDA-9855R/CDA-9853R. This will reduce any chance of damage to the unit in case of a short-circuit.

•Be sure to connect the colour coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle's electrical system.

•When making connections to the vehicle's electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the CDA-9855R/CDA-9853R to the fuse box, make sure the fuse for the intended circuit of the CDA-9855R/CDA-9853R has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer.

•The CDA-9855R/CDA-9853R uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized ALPINE dealer for assistance.

•Be sure to connect the speaker (–) leads to the speaker (–) terminal. Never connect left and right channel speaker cables to each other or to the vehicle body.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number or the engraved serial number is located on the bottom of the unit.

SERIAL NUMBER:

INSTALLATION DATE: INSTALLATION TECHNICIAN: PLACE OF PURCHASE:

40-EN

Page 40 Page 42
Image 41
Page 40 Page 42
Contents CDA-9855R DE CDA-9853R Contents Installation and Connections Operating Instructions Never Attempt the Following On handling Compact Discs CD/CD-R/CD-RW Move your finger on the GlideTouch bar to the left or right About the GlideTouch Bar OperationTouch or press the desired position on the GlideTouch bar Getting Started Radio Press TUNE/A.ME to select the tuning modeDetaching and Attaching the Front Panel Listening to RadioAutomatic Memory of Station Presets Manual Storing of Station PresetsTuning to Preset Stations Station Title Search FunctionRecalling Preset RDS Stations Setting RDS Reception Mode and Receiving RDS StationsPress FUNC. to activate the audio function mode Receiving RDS Regional Local StationsPTY Programme Type Tuning PI Seek SettingReceiving Traffic Information Receiving Traffic Information While Playing CD or RadioDisplaying Radio Text Priority PTY Programme Type12-EN GlideTouch bar under P.PTY13-EN PlaybackX. Random Play Repeat PlayScanning Programmes 14-ENFile/Folder Name Search concerning MP3/ WMA Searching from CD TextQuick Search About MP3/WMA16-EN TerminologyEqualizer Presets Sound SettingSetting Users EQ mode 17-ENAdjusting and Storing the Graphic Equalizer Curve Adjusting and Storing the Parametric Equalizer CurveAdjust the level by turning the Rotary encoder Press SOURCE/POWER to set the band width QRecalling the Stored Equalizer Curve Way modeAbout the Crossover 19-ENPress SOURCE/POWER to adjust the slope Adjusting and Storing the Crossover SettingsAdjust the output level by turning the Rotary encoder WAY SystemAbout Time Correction Recalling the Stored Crossover SettingsExample 1. Listening Position Front Left Seat Example 2. Listening Position All SeatsAdjusting and Storing the Time Correction Setting the Time Correction UnitDisplay Setup menu is displayed 22-ENSetting the MX Mode Recalling the Stored Time Correction SettingsAbout the MX indicator display CDA-9853R only 23-ENDisplaying the Title/Text Other Functions24-EN Press Title25-EN Titling Discs/StationsAbout Title and Text Press Title and select the Title DisplayErasing Disc Title/Station Title Setting Amplifier LinkIf a Mono Amplifier is Connected If a 4ch Amplifier is ConnectedChanging the Lighting Colour of All the Buttons Setting the Multicolour IlluminationIf you want to use colours other than the above 27-ENData Downloading About i-Personalize28-EN File name of download data shall be AU*****.MP3Playing MP3/WMA Data Play Mode General SettingSetup menu of the selected item is displayed 29-EN30-EN Tuner Setting31-EN Audio SettingDisplay Setting 32-EN Demo SettingSearching for a desired Song Searching by artist name Searching by PlaylistSearching by album name 33-EN34-EN Random Play Shuffle M.I.XDisplaying the Text Controlling CD Changer Optional Changer OptionalPlaying MP3 Files with the CD Changer Optional Multi-Changer Selection Optional36-EN Remote ControlInformation Battery Replacement CDA-9855R onlyCase of Difficulty BasicIndication for CD Player AudioIndication for CD Changer 38-ENIndication for iPod Mode Specifications39-EN Bottom side of player40-EN Installation and ConnectionsRemoval Installation41-EN 42-EN Connections43-EN Amplifier Link / Vehicle Display Interface ConnectorTo prevent noise/interference in the audio system 44-ENCHM-S630 CHA-S634 CHA-1214 Alpine CD Changers Give You MoreAppendix Q9 no
Top Page Image Contents