Alpine VPA-B222R owner manual Using the Speaker Input, Setting the Speaker Input Mode, 16-EN

3 Press the joystick up or down to select the desired item.

Setting items:

IN-INT MUTE / NAV. / GUIDE MIX / NAV. MIX LV / FACT SYS SET

/FACT SYS LV / FACT SYS DET / FACT SYS MIX / F.SYS MIX TYP

/F.SYS INT CH. / REMOTE SEL.*1 / AUX IN-1(2,3) / AUX IN- 1(2,3) NAME / AUX IN-1(2,3) LEVEL / MONITOR-1 / MONITOR-2

/VISUALIZER / ILLUM COLOR / CMNDR LIGHT. / DIMMER / SCREEN ADJ / SUBW*2

*1 Refer to "Rear Entertainment Function" on page 12.

*2 When an external audio processor is connected, the SUBW item is not displayed.

4 Press the joystick left or right to adjust and set the desired item.

5 Press TA/RTN/SETUP to return to the previous screen. Press TA/RTN/SETUP repeatedly to return to the main source screen displayed before starting the setup operation.

•Select SETUP on the FUNCTION screen to recall the SETUP screen after pressing and holding /MENU/FUNC. for at least 2 seconds.

•Immediately after changing the settings of System Mode (While the system is writing data automatically) do not turn the ignition key (engine key) to OFF. Otherwise, the settings may not be changed.

Using the Speaker Input

The unit can interrupt the system (navigation or telephone) of the car. The audio can also be played back on the unit if the car system of the audio (CD, etc.) is selected as the source.

The unit makes the sound interruption according to the sound output level of the car system. If any of the following settings are not correctly made, sound may not interrupt, or loud sound may suddenly interrupt.

Setting the Speaker Input Mode

The following explains how to install the system (navigation/telephone) in your car. While listening to the radio, you can have navigation voice guidance or a received telephone call interrupt automatically. You can also select the speaker input mode (FACTRY SYS) on the source selection screen.

Setting items: FACT SYS SET

Setting content: OFF / SOURCE / INT / BOTH

SOURCE: The system (CD, etc.) of the car can be selected as a source.

Navigation/telephone voice of the car is not interrupted.

INT: Interrupts only the navigation/telephone voice of the car.

BOTH: The system (CD, etc.) of the car can be selected as the source.

Navigation/telephone voice of the car is interrupted.

OFF: Operation and setting of the speaker input mode is not performed.

•If the car system (CD, etc.) is set to SOURCE and played back in a car with multi-channel speakers, sound such as treble, etc., may not be correctly output.

•Depending on the conditions of use, the INT or SOURCE setting is recommended.

•If INT is set, do not output CD audio from the car system.

•With BOTH set, if the source is set to other than FACTORY SYS, do not output CD audio, etc., from the car system.

•If OFF is to set, speaker input mode settings cannot be made.

Displaying the Speaker Input Volume Level

The volume level of the speaker input is displayed numerically. Adjustment can be made only on the system in your car (standard car audio, etc.), and cannot be made by this unit.

Setting items: FACT SYS LV

Setting content: 0 to 2 L / 3 to 15: OK / 16 to 18 H

L:Volume level is LOW

OK: Volume level is optimally adjusted

H:Volume level is HIGH

Adjust the volume for optimum level.

•Set the volume as loud as possible, but before the onset of distortion (The volume level should not exceed 15). Even if OK is displayed, if any distortion is apparent, decrease the car audio's volume.

•Turn off the car audio's TREBLE, BASS settings.

•The volume level cannot be displayed when OFF is set in "Setting the Speaker Input Mode" (page 16).