Alpine IVA-D300 Speaker Setup, Setting of Dolby 5.1ch, Adjusting the acoustic image, 48-EN

Speaker Setup

The PXA-H700 or PXA-H701 can be set according to the playable frequency range of your speakers.

Check the playable frequency range of the speakers (not including the subwoofer) before performing this operation to verify whether the speakers can play low frequencies (of about 80 Hz or less).

•Avoid stopping, pausing, switching the disc, cueing, fast- forwarding or switching the audio channel of this unit while making this adjustment. The setting is canceled if Decode mode is switched.

1 Check that Defeat mode is off (page 22). 2 Touch [SYS.] on the main source screen.

The SYSTEM selection screen appears.

3 Touch [i-Personalize].

The i-Personalize screen will appear.

4 Touch [] of A.PROCESSOR.

The A.PROC list screen appears.

5 Touch [] of SPEAKER SETUP.

The adjusting screen of SPEAKER SETUP appears.

6 Select the speaker characteristic by touching [;] or [:] of the desired speaker setting.

OFF∗1: When no speaker is connected.

SMALL: When a speaker that cannot play low frequencies (80 Hz or less) is connected.

LARGE∗2: When a speaker that can play low frequencies (80 Hz or less) is connected.

∗1 It is not possible to set the front speakers to “OFF”. ∗2 If the front speakers are set to “SMALL”, the rear and

center speakers cannot be set to “LARGE”.

•If the center speaker is turned “OFF,” the center channel's audio signals are added to the audio signals output from the front speakers.

•If you set the speaker response to “OFF,” also set the speaker setting to “OFF.” (page 44)

•Perform the setup for all the speakers (“Front,” “Center,” “Rear” and “Subwoofer”). If not, the sound may not be balanced.

•When center is set to “OFF”, the setting is ineffective even if center is set with this function.

•Through changing the settings on each speaker, a change in the output of the other speakers may occur due to the setting requirements.

•When using the PRO LOGIC II, if the rear speaker is set to “LARGE”, then there will be no output from the subwoofer.

Setting of Dolby 5.1ch

1 Check that Defeat mode is off.

2 Touch [SYS.] on the main source screen.

The SYSTEM selection screen appears.

3 Touch [i-Personalize].

The i-Personalize screen will appear.

4 Touch [] of A.PROCESSOR.

The A.PROC list screen appears.

5 Touch [] of DOLBY 5.1 CH SETUP.

The DOLBY 5.1CH SETUP display appears.

Set the items below as you desire.

Adjusting the acoustic image

In most installations, the center speaker must be placed directly between the front passenger and driver. Using this function, the center channel information is distributed to the left and right speakers. This creates an acoustic image simulating a center speaker directly in front of each listener. Adjusting the center width in PL II MUSIC (see “Using the Pro Logic II Mode,” page 50), makes this function ineffective.

•Avoid stopping, pausing, switching the disc, cueing, fast- forwarding or switching the audio channel of this unit while making this adjustment. The setting is canceled if the Decode mode is switched.

Touch [;] or [:] of BI - PHANTOM to adjust the level.

The level can be adjusted within the range of -5 to +5. The higher the level, the more the position of the center speaker is shifted to the sides.

The BI-PHANTOM function is turned off by touching

[OFF].

•This adjustment is effective when the setting of the center speaker to SMALL or LARGE in the speaker setup settings.

•This adjustment is ineffective when the speaker is set to CENTER OFF in “Setting the Speakers” (page 44).

Mixing bass sound to the rear channel

This function mixes the front channel audio signals to the audio signals output from the rear speakers, improving the sound in the vehicle’s rear seat.

•Avoid stopping, pausing, switching the disc, cueing, fast- forwarding or switching the audio channel of this unit while making this adjustment. The setting is canceled if the Decode mode is switched.

Touch [;] or [:] of REAR MIX to adjust the level.

The level can adjusted in five steps: –6, –3, 0, +3 and +6. The higher the level, the more bass is output from the rear speakers. (The effect differs according to the software (DVD, etc.).)

The REAR MIX function is turned off by touching [OFF].

•This adjustment is ineffective when the rear speaker setup setting is set to “OFF.”

•For linear PCM signals, the voice is output from the rear speaker regardless of the REAR FILL and REAR MIX setting.

48-EN