Sony MDS-JB920 Section Test Mode, Precautions for USE of Test Mode, Setting the Test Mode

Page 18

SECTION 4

TEST MODE

1. PRECAUTIONS FOR USE OF TEST MODE

• As loading related operations will be performed regardless of the test mode operations being performed, be sure to check that the disc is stopped before setting and removing it.

Even if the [ÊÊÊÊÊEJECT]¤ button is pressed while the disc is rotating during continuous playback, continuous recording, etc., the disc will not stop rotating.

Therefore, it will be ejected while rotating.

Be sure to press the [ÊÊÊÊÊEJECT]¤ button after pressing the [MENU/NO] button and the rotation of disc is stopped.

1-1. Recording laser emission mode and operating buttons

•Continuous recording mode (CREC MODE)

•Laser power check mode (LDPWR CHECK)

•Laser power adjustment mode (LDPWR ADJUST)

•Traverse (MO) check (EF MO CHECK)

•Traverse (MO) adjustment (EF MO ADJUST)

•When pressing the [ÊÊÊÊÊREC]r button.

2. SETTING THE TEST MODE

The following are two methods of entering the test mode.

Procedure 1: While pressing the [ÊÊÊÊÊÊÊÊAMSÊÊÊÊÊÊÊÊ]- ± knob and [ÊÊ]p button, connect the power plug to an outlet, and release the [ÊÊÊÊÊÊÊÊAMSÊÊÊÊÊÊÊÊ]- ± knob and [ÊÊ]p button.

When the test mode is set, “[Check]” will be displayed. Rotating the [ÊÊÊÊÊÊÊÊAMSÊÊÊÊÊÊÊÊ]- ± knob switches between the following four groups; ···NnCheck NnAdjust NnService NnDevelop Nn···.

Procedure 2: While pressing the [ÊÊÊÊÊÊÊÊAMSÊÊÊÊÊÊÊÊ]- ± knob, connect the power plug to the outlet and release the [ÊÊÊÊÊÊÊÊAMSÊÊÊÊÊÊÊÊ]- ± knob. When the test mode is set, “TEMP CHECK” will be displayed. By setting the test mode using this method, only the “Check” group of method 1 can be executed.

3. EXITING THE TEST MODE

Press the [REPEAT] button. The disc is ejected when loaded, and “Standby” display blinks, and the STANDBY state is set.

4. BASIC OPERATIONS OF THE TEST MODE

All operations are performed using the [ÊÊÊÊÊÊÊÊAMSÊÊÊÊÊÊÊÊ]- ± knob, [YES] button, and [MENU/NO] button. The functions of these buttons are as follows.

Function name	Function

[ÊÊÊÊÊÊÊÊAMSÊÊÊÊÊÊÊÊ]- ± knob	Changes parameters and modes

YES button	Proceeds onto the next step. Finalizes input.
MENU/NO button	Returns to previous step. Stops operations.

– 18 –

Image 18

Contents Specifications MDS-JE520MDM-5A SELF-DIAGNOSIS Function GeneralItems of Error History Mode Items and Contents Table of Contents DiagramsSection Servicing Notes Flexible Circuit Board Repairing VarningVaroitus JIG for Checking BD Board Waveform IOPRecord Precedure Checks Prior to Parts Replacement and Adjustments Forced ResetREC/PLAY Retry Cause Display Mode PrecedureHexadecimal nBinary Conversion Table Section General Location of ControlsFront view Rear view Page Page Section Disassembly CaseFront Panel Seciton Main BoardMechanism Section MDM-5A Slider CAMBase Unit MBU-5A, BD Board SW BOARD, Loading Motor M103Setting the Test Mode Section Test ModePrecautions for USE of Test Mode Exiting the Test ModeSelecting the Test Mode Display Contents Mark GroupOperating the Continuous Playback Mode Non-Volatile Memory Mode EEP ModeMID Auto gain display Not used in servicing Test Mode DisplaysFunctions of Other Buttons Detrack check display Not used in servicingDisplay Contents When Lit When Off Meanings of Other DisplaysSection Electrical Adjustments Parts Replacement and AdjustmentPrecautions for Adjustments Precautions for Checking Laser Diode EmissinonPrecautions for USE of Optical PICK-UP KMS-260A Laser power meterCheck Prior to Repairs Temperature Compensation Offset CheckLaser Power Check Traverse CheckFocus Bias Check Play Checking MO Error Rate CheckCD Error Rate Check Self-Recording/playback CheckLaser Power Adjustment Initial Setting of Adjustment ValueTemperature Compensation Offset Adjutment Recording and Displaying the IOP InformationTraverse Adjustment Focus Bias Adjustment CD Auto Gain Control Output Level Adjustment Error Rate CheckAuto Gain Control Output Level Adjustment MO Auto Gain Control Output Level AdjustmentAdjusting Points and Connecting Points Section Diagrams BD Board IC101 CXA2523AR RF AMP, FOCUS/TRACKING Error AMPIC PIN Function Description Xrst SrdtSens SqsyMvci XrasXWE AsyoSprd SrdrSfdr SpfdMain Board IC100 CXD8607N A/D Converter TEST2 AvddlVDD1 LvddMain Board IC800 M30610MCA-264FP System Controller MDS-JB920 REC Analog Block Diagram Servo Section∙ Signal Path REC DigitalBlock Diagram Main Section ∙ Signal Path Play Analog OUTPlay Digital OUT Circuit Boards Location Printed Wiring Boards BD Section MDS-JB920 Schematic Diagram BD /2 See 53 for Waveforms. See page 70 and 71 for IC Block DiagramsWaveforms BD board Main board Disp board MDS-JB920 MDS-JB920 MDS-JB920 MDS-JB920 Other layers pattern Side a US, CND Schematic Diagram Panel Section See page 54 for Waveforms IC Block Diagrams BD Board IC101 Schematic Diagram BD Switch SectionPrinted Wiring Board BD Switch Section CXA2523ARIC121 CXD2654R IC152 BH6511FS-E2IC203 Main Board IC100 CXD8607NIC101 CXA8054M CXA8042ASIC200 CXD8767N SN74HC153ANS SN74HCU04ANS-E20Section Exploded Views Chassis SectionFront Panel Section Supplied with RV760206 201 204 205209 4-988-466-21 Spring ELECTROSTATIC, Leaf Base Unit Section MBU-5A Section Electrical Parts List Diode F1J6TP TANTAL. ChipDiode CXA2523ARDisp Main C252 Mylar CXA8042AS HZS6C1LHZ7.5CP-TK SN74HC153ANS390 LED SEL6210S-TH10 Standby Main PSWCoil with Core Vibrator LED SEL6810A-TH10 Mega Control TransistorSW VOL Sony Corporation