RETRY CAUSE DISPLAY MODE
•In this test mode, the causes for retry of the unit during recording can be displayed on the indication vessel. During playback, the “track mode” for obtaining track information will be set.
This is useful for locating the faulty part of the unit.
•The following will be displayed :
During recording and stop : Retry cause, number of retries, and number of retry errors.
During playback : Information such as type of disc played, part played, copyright.
These are displayed in hexadecimal.
Procedure:
1.Press the @/1 button, x/Z button and u button continuously for about 10 seconds.
2.Rotate the AMS knob to display “Debug Disp”, Then press the AMS button.
3.When the mode is set, “RTs 00c 00e 00” is displayed.
4.Press the z button to start recording. Then press the X button and start recording.
5.To check the “track mode”, press the H button to start play.
6.To exit the test mode, press the @/1 button, and turn OFF the power. If the test mode cannot be exited, refer to “Forced Reset” on page 8.
Fig. 1 Reading the Test Mode Display (During recording and stop)
RTs@@c##c**
Indication vessel display
@@: Cause of retry ## : Number of retries
** : Number of retry errors
Reading the Retry Cause Display
Fig. 2 Reading the Test Mode Display (During playback)
@@###**$$ Indication vessel display
@@ : Parts No. (name of area named on TOC)
### | : Cluster |
** | : Sector } Address (Physical address on disc) |
$$ | : Track mode (Track information such as copyright infor- |
| mation of each part) |
| Higher Bits | Lower Bits | Hexa- |
|
| |||||||
|
|
|
|
|
|
|
|
| Cause of Retry | Occurring conditions | ||
Hexadecimal | 8 | 4 | 2 | 1 | 8 | 4 | 2 | 1 | ||||
decimal | ||||||||||||
|
|
|
|
|
|
|
|
|
|
| ||
Bit | b7 | b6 | b5 | b4 | b3 | b2 | b1 | b0 |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |
Binary | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 01 | shock | When track jump (shock) is detected | |
|
|
|
|
|
|
|
|
|
|
|
| |
| 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 02 | ader5 | When ADER was counted more than five times continu- | |
| ously | |||||||||||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |
| 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 04 | Discontinuous address | When ADIP address is not continuous | |
|
|
|
|
|
|
|
|
|
|
|
| |
| 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 08 | DIN unlock | When DIN unlock is detected | |
|
|
|
|
|
|
|
|
|
|
|
| |
| 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 10 | FCS incorrect | When not in focus | |
|
|
|
|
|
|
|
|
|
|
|
| |
| 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 20 | IVR rec error | When ABCD signal level exceeds the specified range | |
|
|
|
|
|
|
|
|
|
|
|
| |
| 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 40 | CLV unlock | When CLV is unlocked | |
|
|
|
|
|
|
|
|
|
|
|
| |
| 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 80 | Access fault | When access operation is not performed normally | |
|
|
|
|
|
|
|
|
|
|
|
| |
Reading the Display:
Convert the hexadecimal display into binary display. If more than two causes, they will be added.
Example
When 42 is displayed:
Higher bit : 4 = 0100 t b6
Lower bit : 2 = 0010 t b1
In this case, the retry cause is combined of “CLV unlock” and “ader5”.
When A2 is displayed:
Higher bit : A = 1010 t b7+b5
Lower bit : 2 = 0010 t b1
The retry cause in this case is combined of “Access fault”, “IVR rec error”, and “ader5”.
9