GE HE500TIU050, IC300TIU201, IC300TIU101, HE500TIU100, HE500TIU113 TIU050 Dimensions, TIU050 Cutout

Page 16

CH.2: TIU050	06 Apr 2000	PAGE 17
		GFK-1819

Pull-upand Pull-downswitches are used to increase the signal level on the RS-485 bus. This is useful if there is a long bus and a significant amount of attenuation is anticipated.

Termination resistance of 120Ω must be placed across each end of the RS-485 bus. With switch 2 ON, a 120Ω resistance is placed across the bus. This is only used if the TIU050/100/110 is the last device at either end of the bus.

2.5TIU050 Dimensions

5.95” [151mm]

3.27”+-00.0.002[83+-00.0.5mm]

UP TO 0.04”[1mm] CORNER

RADIUS IS ACCEPTABLE

TIU050 CUTOUT DETAILS

TOLERANCES ARE +/- 0.01” [0.3mm] UNLESS STATED OTHERWISE

Figure 2.5 – TIU050 Cutout

Image 16

Contents Operator Station Hardware Manual Preface Declaration of EMC Conformity About Programming Examples06 Apr Table of Contents Networks Scope IntroductionOperator Station OS Product Line Fanuc Channels CH Introduction Equipment Needed CH Introduction 06 Apr GFK-1819 Technical Specifications Parameter Conditions Min Typical Max UnitsGFK-1819 Upgrade Revision Software & Firmware Software UpgradeFirmware Upgrade Scope06 Apr GFK-1819 CH Introduction TIU050 TIU050 Contrast AdjustmentCH.2 TIU050 06 Apr GFK-1819 Configuration Bank 1 TIU050 Configuration of the RS-485 Port06 Apr CH TIU050 GFK-1819 TIU050 Ports TIU050 Dimensions TIU050 Cutout06 Apr CH TIU050 GFK-1819 TIU10X Contrast Adjustment CH TIU100/101/102/103 06 Apr GFK-181906 Apr CH.3 TIU100/101/102/103 GFK-1819 Tiux Rear View Rear View of TIU100/101/102 TIU100 Ports1 TIU10X Configuration of the RS-485 Port Automation Equipment Port Receive Transmit LEDsTIU10X Dimensions 06 Apr CH.3 TIU100/101/102/103 GFK-1819TIU11X Contrast Adjustment CH TIU110/111/112/113 06 Apr GFK-181906 Apr CH TIU110/111/112/113 GFK-1819 TIU11X Rear View Rear View of TIU11X TIU110 PortsSerial P ort TIU11X Dimensions 1 TIU11X Configuration of the RS-485 Port06 Apr CH TIU110/111/112/113 GFK-1819 CH TIU200/201/202/203 06 Apr GFK-1819 Front View of TIU20X TIU20X Button Selection ActionsRear View of TIU20X TIU20X Ports Automated Equipment Serial PortLED’s flash when the TIU20X Is communicating with the AE TIU20X Dimensions 1 TIU20X Configuration of the RS-485 Port06 Apr CH TIU200/201/202/203 GFK-1819 Communications PC to Operator Station CommunicationsRecommended Automation Equipment Communication Cables RS-232 ConnectionGFK-1819 RS-422/485 Four-Wire TIU110/10006 Apr GFK-1819 RS-485 Two-Wire GFK-1819 Current Loop + SRGetting Started Self-TestGFK-1819 Updating the Protocol Select Update TIU Protocol from the File menuProtocol Name Software Revision Terminal Type Scope Controller Area Network can Overview NetworksCsCAN Network Overview DeviceNet Features DeviceNet OverviewDeviceNet Protocol DeviceNet OperationGFK-1819 Can Wiring Rules Can Network CablingProfibus Wiring 06 Apr GFK-1819 ProfibusE term in atio n H m Installing and Removing a SmartStack Module Installing SmartStack ModulesSmartstack  Removing SmartStack ModulesCH Smartstack