Cateye GB-300R Connecting the device to Playstation2, How to adjust the Controller

Page 6

Connecting the device to Playstation2

This controller is compatible with the “Playstation2”. Plug the connector of this device into the controller terminal located at the front of the “Playstation2”. Consult the operating manual of the “Playstation2” unit, if necessary.

ENG

Important: If the GBF PRO RECUMBENT BIKE does not operate after connecting it to the PlayStation2 unit, disconnect it and reconnect it again.

Reference: It is possible for two players to play simultaneously by connecting two GBF PRO RECUMBENT BIKEs or connecting to a general controller.

“Playstation2” unit

Controller connector

 

1P side

To GBF PRO RECUMBENT BIKE Controller

2P side

 

How to adjust the Controller

Adjusting the steering sensitivity

Turn on the “Playstation2”. Slide the controller’s steering sensitivity level control and check the operation of the GBF PRO RECUMBENT BIKE steer- ing on the Race Screen. Adjust the steering sensitivity to a suitable level.

Caution Depending on the software, if the steering sensitivity is set to Min. when the steering is turned from left to right, the steering reaction does not work for the game.

Adjusting the speed sensitivity

Turn on the “Playstation2”. Slide the controller’s speed sensitivity level control and check the GBF PRO RECUMBENT BIKE pedals on the Race Screen. Adjust the speed sensitivity to a suitable level.

Caution Depending on the software, while pedaling, the speed of the game does not register.

This will cause the game not to move forward.

Steering sensitivity

 

L

R

Max.

STEERING LEVEL

SPEED LEVEL

Min.

 

 

SELECT

START

 

 

ANALOG

STEERING LEVEL

Speed sensitivity

L

R

 

STEERING LEVEL

SPEED LEVEL

Fast

 

Slow

SELECT

START

 

 

ANALOG

 

SPEED LEVEL

Button Function change

In the case of software with different button functions, change functions as follows:

The buttons to which functions can be assigned are green, pink, red, blue, L1, L2, R1 and R2.

<Operation>

Keep pressing the SELECT button until the following steps are completed: 1.Press the blue (or pink) button depending on the function to be changed.

The LED will change from constantly lit to blinking.

2.Press the default accelerator (or brake) button in the software currently being used.

The LED will change stop blinking and will be lit continuously, signifying that the function change is now complete. (If analog mode is OFF, the LED will be off, signifying that the function change has been completed.)

Revert to the original button function

While pressing the SELECT button, press the speed button (blue) or brake button (pink).

Controller Cover Care

While using GBF PRO RECUMBENT BIKE, the user may perspire/sweat while training.

To prevent sweat from getting into the controller, please use the controller cover provided.

Please wash and dry after use.

Controller cover

Controller

FCC

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

6

Image 6
Contents Symbol marks used for safety precautions in this manual Symbols LegendFitness Safeguards Model GB-300RPackage Contents How to assemble GBF PRO Recumbent Bike Installing the seat handle Installing the consoleConnecting the controller Installing the seat cushionAdjusting the Components GBF PRO Recumbent Bike ControllerButton Function change Connecting the device to Playstation2How to adjust the Controller Controller Cover CareGBF PRO Recumbent Bike Console Mounting Batteries Trying out the GBF PRO Recumbent Bike for the first timeEntering target calorie consumption Training with TargetsEntering target distance Entering upper and lower heart rate limitsBe sure the seat cushion is tight How to Select a ProgramDaily inspection Be sure the seat handle is tight and not loose or rattlingTroubleshooting Actual steering operation Properly? Ing sensitivitySpare Parts SpecificationsWarranty / Repairs. Service Optional Parts本文中のマークの意味 安全にお使いいただくためにフィットネス安全指導 重要な注意梱包内容の確認 GBF Pro リカンベントの組み立て コントローラーブラケットの取り付けシートベースの取り付け 各部の調整 コントローラーの説明ボタン機能の変更 プレイステーション 2 との接続コントローラーの調整方法 コントローラーカバーについてコンソールの説明 電池の装着 まず乗ってみましょう目標を設定してのトレーニング 目標時間の入力プログラムを選択します 日常点検トラブルと処理 まずゲームをリセットし、症状が改善されていないかを確認します。 トラブル チェック項目オプション部品 製品仕様補修部品 保証修理サービスについて