NordicTrack NTL07007.3 manual Operation and Adjustment, PRE-LUBRICATED Walking Belt

Page 12

OPERATION AND ADJUSTMENT

THE PRE-LUBRICATED WALKING BELT

Your treadmill features a walking belt coated with high- performance lubricant. IMPORTANT: Never apply sil- icone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

DANGER: Improper connection of the equipment-grounding conductor can result in an increased risk of electric shock. Check with a qualified electrician or service- man if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product—if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Your treadmill, like any other type of sophisticated electronic equipment, can be seriously damaged by sudden voltage changes in your home’s power. Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances being turned on or off. To decrease the possibility of your treadmill being damaged, always use a surge suppressor with your treadmill (see drawing 1 at the right). To purchase a surge suppressor, see your local NordicTrack dealer or call the telephone number on the front cover of this manual and order part number 146148, or see your local electronics store.

Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge sup- pressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps. There must be a moni- toring light on the surge suppressor to indicate whether it is functioning properly. Failure to use a properly functioning surge suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change speed, accelerate, or stop unexpect- edly, which may result in a fall and serious injury.

This product must be grounded. If it should malfunc- tion or break down, grounding provides a path of least resistance for electric current to reduce the risk of elec-

tric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. Plug the power cord into a surge suppressor, and plug the surge suppressor into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Important: The treadmill is not compatible with GFCI-equipped outlets.

This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illus- trated in drawing 1 below. A temporary adapter that looks like the adapter illustrated in drawing 2 may be used to connect the surge suppressor to a 2-pole receptacle as shown in drawing 2 if a properly grounded outlet is not available.

1

Grounded Outlet Box Surge Suppressor

Grounding Pin

Grounding Pin

Grounded Outlet

Grounding Plug

 

2

Grounded Outlet Box

Adapter

Surge Suppressor

Lug

Metal Screw

The temporary adapter should be used only until a properly grounded outlet (drawing 1) can be installed by a qualified electrician.

The green-colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used it must be held in place by a metal screw. Some 2-pole receptacle outlet box covers are not grounded. Contact a qualified elec- trician to determine if the outlet box cover is grounded before using an adapter.

12

Image 12
Contents QUESTIONS? Model No. NTL07007.3 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unplugged See the inset drawing. Tie the wire tieDo not fully fold the Frame yet Nut the Wheel must turn freely. DiscardBe careful not to pinch the Upright Wire Fully tighten the Bolts yetSee assembly steps 4 and 6. Firmly tighten the 3/8 x 4 Bolts Pull on the sleeve to make sure that it is locked into place Be careful not to pinch the wires. Reattach Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Start the walking belt and adjust the speedMonitor your progress with the displays Matrix-When you Change the incline of the treadmill as desiredTime/Incline dis Measure your heart rate if desired HOW to USE a Preset Workout Select a preset workoutPress the Start button to start the workout HOW to USE the Custom Workout Center Select the Custom Workout CenterPress the Start Workout button to start the workout HOW to USE the Fitness Test Workout Put on the chest pulse sensorSelect the fitness test workout Press the Start Fitness Test button to start the workoutHOW to USE the Sound System Connector is fully pluggedHOW to USE AN Ifit Card Insert an iFIT card and select a workoutInformation Mode HOW to Adjust the Cushioning SystemOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches R0108A Key No. Qty DescriptionQty Exploded Drawing A-Model No. NTL07007.3 Exploded Drawing B-Model No. NTL07007.3 Exploded Drawing C-Model No. NTL07007.3 Exploded Drawing D-Model No. NTL07007.3 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT