7. Set the console assembly face down on a soft | 7 |
|
|
|
surface to avoid scratching the console assem- |
|
|
| |
|
|
|
| |
bly. Hold the Right Handrail (95) near the con- |
|
|
|
|
sole assembly. Next, insert the console wire into |
|
| Console | |
the large hole in the Right Handrail and out of |
|
| ||
|
| Wire |
| |
the top as shown. If necessary, use needlenose |
|
|
| |
|
|
|
| |
pliers to help pull the console wire out. | 95 | 1 | Hole |
|
|
| |||
Attach the Right Handrail (95) and the Left |
|
|
| 1 |
Handrail (not shown) with four #8 x 3/4" Screws |
|
|
|
|
(1) (two are shown). Make sure that no wires |
|
|
|
|
are pinched. Start all four Screws before |
|
|
|
|
tightening any of them; do not overtighten |
|
|
|
|
the Screws. |
|
|
|
|
|
|
|
| Console |
|
|
|
| Assembly |
8. Tighten a 1/4" x 1 1/4" Bolt (5) with a 1/4" Star | 8 |
|
|
|
Washer (33) into the bracket and Handrail |
|
|
| |
|
|
|
| |
Crossbar (94) on each side of the console as- |
|
| 5 | Wire |
sembly (only one side is shown). |
|
| ||
|
|
| Tie | |
|
|
| 33 | |
|
|
|
| |
Remove the wire tie from the console wire. |
|
|
|
|
| Console |
|
|
|
| Assembly |
|
| 94 |
|
|
|
| |
9. Remove the long tie from the Upright Wire (38). | 9 |
|
|
|
| Console |
|
| |
|
|
|
| |
Have a second person hold the console assem- |
| Assembly |
|
|
bly near the Right Upright (78) and the Left |
|
|
|
|
Upright (not shown). Connect the Upright Wire |
|
|
|
|
(38) to the console wire. See the inset drawing. |
|
|
|
|
The connectors should slide together easily |
|
|
|
|
and snap into place. If they do not, turn one | Console |
|
| |
connector and try again. IF THE CONNECTORS |
|
| ||
Wire |
|
|
| |
ARE NOT CONNECTED PROPERLY, THE |
|
|
| |
|
|
|
| |
CONSOLE MAY BE DAMAGED WHEN THE |
|
|
|
|
POWER IS TURNED ON. | 78 |
|
|
|
| 38 |
| Console | |
Attach the console assembly to the Right Upright |
| Long | Wire | |
|
| |||
(78) and the Left Upright (not shown) with four |
|
|
| |
|
| Tie |
| |
5/16" x 3 1/4" Bolts (7) and four 5/16" Star |
|
|
| |
| 10 |
|
| |
Washers (10) (only two are shown). Be careful |
|
| 38 | |
not to pinch the wires. | 7 |
|
| |
|
|
|
| |
See steps 4 and 6. Tighten the four 3/8" x 5" |
|
|
|
|
Bolts (6). |
|
|
|
|
| 9 |
|
|
|