HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room tem- perature before turning on the power. If you do not do this, the console displays or other electrical components may become damaged.
Plug in the power cord |
|
|
|
|
|
|
(see page 9). Next, locate |
|
|
|
|
|
|
the reset/off circuit |
| Reset |
|
|
|
|
|
|
|
|
| ||
breaker on the treadmill |
| Position |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| |
frame near the power |
|
|
|
|
|
|
|
|
|
|
|
| |
cord. Switch the circuit |
|
|
|
|
|
|
|
|
|
|
|
| |
breaker to the reset posi- |
|
|
|
|
|
|
tion. |
|
|
|
|
|
|
IMPORTANT: The console features a display demo mode, designed to be used if the treadmill is dis- played in a store. If the displays light as soon as you plug in the power cord and switch the circuit breaker to the reset position, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays remain lit, see THE USER’S MODE on page 18 to turn off the demo mode.
Next, stand on the foot rails of the treadmill. Find the clip attached to the key (see the drawing on page 10) and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment, the displays will light. IMPORTANT: In an emergency situation, the key can be pulled from the console, causing the walking belt to slow to a stop. Test the clip by carefully taking a few steps backward; if the key is not pulled from the console, adjust the posi- tion of the clip.
HOW TO USE THE MANUAL MODE
1.Insert the key into the console.
See HOW TO TURN ON THE POWER above.
2.Select the manual mode.
When the key is |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
inserted, the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| ||
manual mode will |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
be selected. If a |
|
|
|
|
|
|
| ||
program has |
|
|
|
|
|
|
|
|
|
|
|
|
| Track |
|
|
| ||
been selected, |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
reselect the man- |
|
|
|
|
|
| |||
ual mode by pressing the Program Select button repeatedly until a track appears in the matrix.
3.Start the walking belt.
To start the walking belt, press the Start button, the 1 Step Speed increase button, or one of the speed buttons numbered 1 through 10.
If the Start button or the
1 Step Speed increase button is pressed, the walking belt will begin to
move at 1 mph. As you exercise, change the
speed of the walking belt as desired by pressing the 1 Step Speed increase and decrease buttons. Each time a button is pressed, the speed setting will change by 0.1 mph; if a button is held down, the speed setting will change in increments of 0.5 mph. Note: After the buttons are pressed, it may take a moment for the walking belt to reach the se- lected speed setting.
If one of the speed buttons numbered 1 through 10 is pressed, the walking belt will gradually increase in speed until it reaches the selected speed setting.
To stop the walking belt, press the Stop button. The time will begin to flash in the Time/Distance display. To restart the walking belt, press the Start button, the 1 Step Speed increase button, or one of the speed buttons numbered 1 through 10.
Note: The first time the treadmill is used, observe the alignment of the walking belt, and align the walking belt if necessary (see page 23).
4. Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the 1 Step Incline increase and decrease buttons. Each time a button is pressed, the incline will change by
0.5%. To change the incline quickly, press one of the incline buttons numbered 0 through 12. Note: After the buttons are pressed, it may take a mo- ment for the treadmill to reach the selected incline setting.
11