NordicTrack 30705.0 user manual Troubleshooting, Problem The power turns off during use, Top

Page 26

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 10. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch pro- trudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch to the reset position.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch to the reset position.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console.

d. If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and unplug the power cord. Carefully tip the treadmill down as shown in drawing a. Remove the Belly Pan Screws

(85)from the Motor Hood (33). Raise the Upright (20) and carefully remove the Motor Hood.

Locate the Reed Switch (22) and the Magnet (18) on the left side of the Pulley (17). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8" (3 mm). If necessary, loosen the Screw (87), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (33) with the Screws (87). Run the treadmill for a few min- utes to check for a correct speed reading.

a

 

 

20

85

85

 

33

1/8”

17

87

 

22

18

Top

 

View

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Call TOLL-FREE QUESTIONS?Model No Serial No Table of Contents Important Precautions Page Before YOU Begin Assembly Try again. if the Connectors are not Handrail Bolts before tightening themPage 105 Wire Cylinder PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleSelect the user mode HOW to Turn on the PowerHOW to Personalize Console Settings Enter user informationSelect the settings mode HOW to USE the Manual Mode Measure your heart rate if desired Press the Start button to start the program HOW to USE a Cardio ProgramSelect a Cardio program See on Select a Pulse program HOW to USE a Pulse ProgramAdjust the maximum target heart rate setting if desired See on HOW to Create a Record Program Select a Record programHOW to USE a Record Program HOW to USE AN Ifit Card Insert an iFIT Card and select a programHOW to USE the Stereo Sound System Optional Chest Pulse SensorHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Top TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0807A Qty DescriptionDescription Exploded Drawing A-Model Exploded Drawing B-Model No Exploded Drawing C-Model No Exploded Drawing D-Model No Ordering Replacement Parts Limited Warranty
Top Page Image Contents