Horizon Fitness T74 Centering the Running Belt, If the running belt is too far to the right side

Page 15

TENSIONING­THE RUNNING BELT

The running belt has been properly adjusted at the factory before it was shipped. At times the belt can move off-center during shipment.

CAUTION: Running belt should NOT be moving during tensioning. Over-tightening the running belt can cause excessive wear on the treadmill as well as its components. Never over-tighten the belt.

If you can feel a slipping sensation when running on the treadmill, the running belt must be tightened. In most cases, the belt has stretched from use, causing the belt to slip. This is a normal and common adjustment. To eliminate this slipping, turn the treadmill off and tension both the rear roller bolts using the supplied Allen wrench, turning them 1/4 TURN to the right as shown. Turn the treadmill on and check for slipping. Repeat if necessary, but NEVER TURN the roller bolts more than 1/4 turn at a time. Belt is properly tensioned when the slipping sensation is gone.

Belt is too far to the right side

Belt is too far to the left side

CENTERING THE RUNNING BELT

The running belt has been properly adjusted at the factory before it was shipped. At times the belt can move off-center during shipment. Before operating the treadmill, make sure the belt is centered and remains centered to maintain smooth operation.

CAUTION: Do not run belt faster than 1/2 mph while centering. Keep fingers, hair and clothing away from belt at all times.

If the running belt is too far to the right side:

With the treadmill running at 1/2 mph, turn the right adjustment bolt clockwise 1/4 turn at a time (using the supplied Allen wrench). Check the belt alignment. Allow belt to run a full cycle to gauge if more adjustment is needed. Repeat if necessary, until the belt remains centered during use.

If the running belt is too far to the left side:

With the treadmill running at 1/2 mph, turn the right adjustment bolt counter-clockwise 1/4 turn at a time (using the supplied Allen wrench). Check the belt alignment. Allow belt to run a full cycle to gauge if more adjustment is needed. Repeat if necessary, until the belt remains centered during use.

IMPORTANT PRECAUTIONS INTRODUCTION

ASSEMBLY

BEFORE YOU BEGIN

TREADMILL OPERATION

TROUBLESHOOTING CONDITIONING & MAINTENANCE GUIDELINES

15

LIMITED WARRANTY

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Treadmill USER’S Guide Page T R O D U C T I O N Table of ContentsGrounding Instructions Important PrecautionsUse the treadmill only as described in this manual OperationUnpacking S E M B LYParts Included Tools IncludedMast to the Main Frame Open Hardware BAGMast to drag upward Position on its ownRemove console from box and place out of the way See step Tighten all bolts completelyRepeat on other side Tighten all 4 Bolts H S E M B LY T74 onlyYOU’RE Finished Assembly StepHere are just a few of the health benefits of exercise Safety KEYBefore YOU Begin Location of the TreadmillProper Usage FoldingMoving Centering the Running Belt If the running belt is too far to the right sideIf the running belt is too far to the left side Treadmill Operation Monitor Display Heart RatePulse Grips Clear Current Selection Select a WeightSelect a Time Select a LevelIntervals Program Segments O G R a M ManualO G R a M Intervals O G R a M RollingO G R a M Hills O G R a M Weight LossO G R a M Golf T73 model O G R a M Custom 1 Perceived Exertion Level Conditioning GuidelinesExample Target Heart Rate Zone ChartStanding Quadriceps Stretch P S StretchingStretch First Standing Calve Muscle StretchCool Down P S Achieving Your Fitness GoalsKeeping AN Exercise Diary Warm UPWeekly Totals Weekly LOG SheetsDAY Week # Distance Calories Time Monthly Totals Monthly LOG SheetsOperation Common Product Questions TroubleshootingTroubleshooting Treadmill When should I BE Worried about a NOISE?Troubleshooting Heart Rate After Each USE Daily I N T E N a N C EFrame Lifetime Limited Home USE WarrantyPage Customer Tech Support
Top Page Image Contents