JVC CA-FSP5 Adjusting the Volume, Selecting the Display Brightness, Reinforcing the Bass Sound

Page 13

Adjusting the Volume

You can adjust the volume level only while the unit is turned on. The volume level can be adjusted between “VOLUME 0” and “VOLUME40.”

When using the remote control, press

VOLUME

VOLUME + to increase the volume or

 

press VOLUME – to decrease it.

 

When using the unit, turn VOLUME + / – clockwise (+) to increase the volume or counterclockwise (–) to decrease it.

VOLUME

For private listening

Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones.

DO NOT turn off (on standby) the unit with the volume set to an extremely high level; otherwise, a sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source next time. REMEMBER you cannot adjust the volume level while the unit is on standby.

Selecting the Display Brightness

You can change the display brightness only while the unit is turned on.

To change the display brightness, press

DIMMER

DIMMER on the remote control.

 

•Each time you press the button, the display dims and brightens alternately.

Reinforcing the Bass Sound

You can reinforce the bass sound to maintain rich (“AHB 1” and “AHB 2”), full bass at low volume. This function only affects the playback sound, but does not affect your recording.

To get the effect, press AHB (Active Hyper

AHB

Bass) PRO until “AHB 1” or “AHB 2” appears

PRO

 

on the display. The BASS indicator also lights

 

up on the display.

 

BASS

•Each time you press the button, the bass sound change as follows:

AHB 1 AHB 2

AHB OFF (Canceled)

“AHB 2” has much more bass reinforcement effect than “AHB 1.”

To cancel the effect, press AHB PRO until “AHB OFF” appears on the display. The BASS indicator goes off.

Selecting the Sound Modes

You can select one of the 4 preset sound modes. This function only affects the playback sound, but does not affect your recording.

To select the sound modes, press

SOUND

MODE

SOUND MODE on the remote control (or

 

SOUND on the unit) until the sound mode you

 

want appears on the display. The SOUND indicator

 

also lights up on the display.

SOUND

SOUND

• Each time you press the button, the sound modes change as follows:

ROCK POP

FLAT JAZZ CLASSIC (Canceled)

ROCK: Gives a heavy sound. Boosts low and high frequency.

POP: Good for vocal music.

CLASSIC: Good for classical music.

JAZZ: Gives a feeling of live atmosphere. Good for acoustic music.

FLAT: The sound mode is canceled. The SOUND indicator goes off.

– 10 –

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Compact Component System Mises en garde, précautions et indications diverses Instructions for safe use Introduction PrecautionsAbout This Manual Contents Front Panel Location of the Buttons and ControlsFront Panel Become familiar with the buttons and controls on your unitFront Panel Display Window Display WindowRemote Control Remote ControlGetting Started Supplied Accessories Connecting AntennasTurn the AM loop antenna until you have the best reception Connecting SpeakersRelease the finger from the clamp AM antennaBy using audio cords not supplied, connect Connecting Other EquipmentTo remove the speaker grilles To connect audio equipmentSetting the Clock Turning On the PowerCommon Operations Selecting the Sources and Starting PlaySelecting the Display Brightness Adjusting the VolumeReinforcing the Bass Sound Selecting the Sound ModesPresetting Stations Tuning in a StationTuning in a Preset Station Listening to FM and AM BroadcastsPlaying Back the Entire CD Normal Play Playing Back CDs CD/CD-R/CD-RWBasic CD Operations Press CD 3/8Program Play On the remote control only Load a CDPress Prog program Repeat to program other tracks youProhibiting Disc Ejection Tray Lock Playing at Random Random PlayRepeating Tracks Repeat Play On the unit onlyPlaying Back Tapes To play both sides Reverse ModePlaying Back a Tape Press 0for cassette deckRecording on a Tape RecordingCheck the recording direction for the tape Press RECOne Track Recording CD Direct RecordingRepeat steps 2 and 3 to record other tracks you want To stop CD Direct Recording, press 7. The tape stops afterUsing Daily Timer and Recording Timer Using the TimersOn the remote control only Press Sleep Using Sleep TimerHow Sleep Timer actually works Wait for about 5 seconds after specifying the time lengthSymptom TroubleshootingCleaning the unit MaintenanceHandling discs Handling cassette tapesSpecifications Authorized Service Centers Limited Warranty 0401MWMMDWJEM
Top Page Image Contents