Image IMBE53910 user manual Weight Carriage and the Rear Upright are ori- ented as shown

Page 9

11.Press two Carriage Bushings (27) into the ends of the Weight Carriage (22). Press two 50mm Round Inner Caps (25) into the ends of the weight tube on the Weight Carriage.

Insert an M10 x 20mm Bolt (26) into the bracket on the Weight Carriage (22).

Slide the Weight Carriage (22) onto the Rear Upright (2) as shown. Make sure that the

Weight Carriage and the Rear Upright are ori- ented as shown.

12.Press a Carriage Bushing (27) into the top of the Carriage Stop (28) as shown in the inset drawing.

Attach the Carriage Stop (28) to the indicated hole in the Rear Upright (2) with an M8 x 70mm Bolt (30) and an M8 Nylon Locknut (54).

Slide the Rear Upright (2) onto the bracket on the Rear Base (3). Attach the Rear Upright to the Rear Base using two M10 x 65mm Bolts (56), four M10 Small Washers (6), and two M10 Nylon Locknuts (11). Do not tighten the Nylon

Locknuts yet.

13.Press a 50mm Square Inner Cap (10) into each end of the Pulley Bar (53). Slide the bracket on the Pulley Bar into the top of the Rear Upright (2). Attach the Pulley Bar to the Rear Upright using two M10 x 65mm Bolts (56), four M10 Small Washers (6), and two M10 Nylon Locknuts (11).

Attach the Pulley Bar (53) to the Top Crossbar (9) using a Support Plate (57), two M10 x 80mm Bolts (41), and two M10 Nylon Locknuts (11).

Tighten all Nylon Locknuts (11) used in steps 1–13.

14.Identify the High Cable (13), which is the shorter of the two Cables. Route the High Cable up through the indicated slot in the Pulley Bar (53). Make sure the ball is in the indicated location.

Route the High Cable (13) around a Pulley (5) as shown. Attach the Pulley inside the slot in the Pulley Bar (53) using an M10 x 65mm Bolt (56), two M10 Large Washers (58), two Pulley Spacers (15), and an M10 Nylon Locknut (11). Do not overtighten the Nylon Locknut; the Pulley must be able to turn freely.

11

2

 

 

 

Angled End

 

 

 

25

 

 

 

 

 

27

 

Weight Tube

 

27

 

 

 

 

 

22

 

 

25

26

 

 

 

 

12

 

 

27

 

 

 

 

54

 

28

 

 

 

 

11

28

Hole

 

6

 

 

 

30

 

2

 

 

 

 

 

 

6

56

 

 

 

 

 

3

Bracket

 

 

 

13

 

 

10

 

 

 

10

41

53

 

 

 

 

 

 

11

Bracket

 

 

 

 

9

6

 

 

57

 

2

 

 

56

 

11

 

 

14

15

5

 

 

 

 

 

15

 

 

 

53

 

 

11 58

 

 

 

13

58

 

 

 

 

 

Ball

56

 

9

Image 9
Contents QUESTIONS? Model No. IMBE53910 Serial NoCustomer HOT Line Table of Contents Important Precautions Right Side Before YOU BeginPart Identification Chart Assembly Make Things Easier for Yourself Locknuts yet Locknuts yet Tighten the M8 x 20mm Screws 50 used in steps 6 Make sure the Safety Spotters are oriented exactly as shownTighten all Nylon Locknuts 11 used in steps Weight Carriage and the Rear Upright are ori- ented as shownLocknut the Pulley must be able to turn freely Page Do not tighten the M10 Nylon Locknuts 11 yet Page Weight Tube Adjustments Using the Locking BARUsing the Safety Spotters Using Olympic Weights on the LEG Lever Attaching Weights to the Barbell or the Weight CarriageAdjusting the Seat Tightening the CablesAdjusting the PAD Tubes Using the Curl PADAdjusting the Backrest Exercise Guidelines Muscle Chart Cooling DownStaying Motivated Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Part LIST-Model No. IMBE539108941