JVC LVT1364-002B manual Getting Started, Unpacking, Connecting AM MW and FM Antennas

Page 9

Getting Started

Do not connect the AC power cord until all other connections have been made.

Continued

Unpacking

After unpacking, check to be sure that you have all the following items.

The number in parentheses indicates the quantity of each piece supplied.

•FM antenna (1)

•AM (MW) loop antenna (1)

•Remote control (1)

•Batteries (2)

If any item is missing, consult your dealer immediately.

Connecting AM (MW) and FM Antennas

FM antenna (supplied)

FM
75	Ω
COAXIAL

1

	AM
2	LOOP
2

AM (MW) loop antenna (supplied)

1Attach the supplied FM antenna to the FM

75 Ω COAXIAL terminal.

Fasten in up the position which gives you the best reception, then fix it on the wall, etc.

2Connect the supplied AM (MW) loop

antenna to the AM LOOP terminal.

Place the antenna away from the unit and adjust its position for the best reception.

For better reception of both FM and AM (MW)

•Make sure the antenna conductors do not touch any other terminals or connecting cords.

•Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord.

About the supplied FM antenna

The FM antenna supplied with this unit can be used as temporary measure. If reception is poor, you can connect an outdoor FM antenna.

To connect an outdoor FM antenna

Before connecting the antenna, disconnect the supplied FM antenna.

Outdoor FM antenna (not supplied)

Coaxial cable (not supplied)

FM
75	Ω
COAXIAL
AM
LOOP

A 75 Ω antenna with coaxial type connector (IEC or DIN 45325) should be used.

Connecting Speakers

You can connect the speakers using the speaker cords.

1	2,3
	Red
Ò
	Black
Â
Red	Speaker
	Speaker
	cord
Speaker	Black
cord	Black
Right speaker	Left speaker

1Hold the clamp of the speaker terminal.

2Insert the end of the speaker cord into the

terminal.

Match the polarity of the speaker terminals: red cord to

ªand black cord to ·.

3Release your finger from the clamp.

IMPORTANT:

•Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit.

•DO NOT connect more than one speaker to one speaker terminal.

6

Image 9

Contents UX-G4 UX-G3 Important for Laser Products Above ALL Precautions IntroductionAbout This Manual Contents Main Unit Location of the Buttons and ControlsTop view Front viewMain unit Display window Display windowPreset Group /UP, Preset Group /DOWN Remote ControlConnecting Speakers Connecting AM MW and FM AntennasGetting Started UnpackingPutting the Batteries into the Remote Control Connecting Other EquipmentTo remove the speaker grilles To connect an audio equipmentTurning On the Power Setting the ClockCommon Operations Turning Off the Unit Automatically Auto StandbySelecting the Source Adjusting the VolumeSelecting the Sound Modes Reinforcing the Bass SoundPlaying Back the Entire Disc-Normal Play Playing Back DiscsPress Open on top of the unit Place a disc correctly with its label side upBasic Disc Operations Programming the Track Playing Order -Program PlayPress CD 3/8 Repeating Tracks-Repeat PlayPlaying at Random-Random Play On the remote control only Press RandomDisplaying the Remaining Time during Playback Press Remain repeatedlyPlaying Back a Tape Playing Back TapesTuning in to a Station Presetting StationsListening to FM and AM MW Broadcasts Tuning in to a Preset Station Receiving FM Stations with RDSChanging the RDS Information Press ¢ or 4 or UP ¢ or Searching for Programs by PTY Codes PTY SearchDown 4 on the unit If no program is found, no MatchSet the volume level to the minimum position Press AUX Using an External EquipmentListening to the External Equipment For operation of the external equipmentRecording To record on both sides-Reverse ModeRecording on a Tape Press REC recordingRecording Discs Disc Synchronized Recording When making Sleep Timer settings while RecordingPlayback Repeatedly until Is litUsing Daily Timer and Recording Timer Using the TimersActivate-Daily 1, Daily 2, Daily 3, or Rec Set the on-time you wantPress and hold Daily TIMER/ Snooze on the unit Using Snooze TimerPress STANDBY/ON to turn Off the unitUsing Sleep Timer On the remote control only Press SleepHow the Sleep Timer actually works Cleaning the unit MaintenanceHandling discs Handling cassette tapesTroubleshooting SymptomPossible Cause Action Specifications UX-G4/UX-G3 Micro Component System