Healthrider HREL69011 manual Installing the Receiver for the Optional Chest Pulse Sensor

Page 8

8.Identify the Left Pedal (13). Attach the Left Pedal to the left Flex Bar (14) with an Adjustment Bolt (20), an M10 Washer (38), and an Adjustment Knob (15) as shown.

Note: The Left Pedal can be attached in any of five positions (see HOW TO ADJUST THE PEDALS on

page 9).

Attach the Right Pedal (not shown) in the same way. Make sure that both Pedals are in the same position.

8
	20
13
14	38
	38
	15

9. Make sure that all parts of the elliptical crosstrainer are properly tightened.	Note: Some hardware may
be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical crosstrainer.

INSTALLING THE RECEIVER FOR THE OPTIONAL CHEST PULSE SENSOR

If you purchase the optional chest pulse sensor (refer to page 20), follow the steps below to install the receiver and the short jumper wire included with the chest pulse sensor.

1. Remove the two short screws and the two long screws

from the back of the Console (5). Lift off the front of the Console.

2.Plug the short jumper wire (A) into the indicated jack on the Console (5). Connect the other end of the short jumper wire to the wire on the receiver (B). Note: Any other wires included with the chest pulse sensor are

not needed.

Next, peel the paper off the adhesive pad on the back of the receiver (B). Orient the receiver as shown, and press it onto the Console (5) in the indicated location.

Refer to step 1 above. Reattach the front of the Console (5) with short screws and the long screws.

Make sure that no wires are pinched.

1	5
	5	Lift
		Lift
		Here
	Short
	Screws
	Long
	Screws
2	B
	B
		Cylinder
	5
	Jack	A

8

Image 8

Contents Customer HOT Line QUESTIONS?To Avoid Unnecessary Table of Contents Important Precautions Always hold the handgrip pulse sensor orFront Left SideAdjustable wrench A rubber mallet AssemblyAssembly requires two persons Lower Wire Harness Wire HarnessDo not pinch the Wire Harnesses Pinch the wire harnessesBattery compartment Handlebar LegsTwo M8 Nylon Locknuts Handlebar Leg must be able to pivot freelyInstalling the Receiver for the Optional Chest Pulse Sensor Make sure that no wires are pinchedHOW to USE the Handlebars HOW to Exercise on the Elliptical CrosstrainerStop Tions Always hold the handgrip pulse sensor orTo your VCR Videocassettes are Features of the ConsoleAddition, you can connect the elliptical crosstrainer Console Description Important The target pace is aHOW to USE the Manual Mode Follow your progress with the feedback modes HOW to USE a Smart ProgramSelect one of the eight Smart programs HOW to USE a Heart Rate Program Select one of the two Heart Rate programsEnter your age Start the programHOW to Connect Your CD PLAYER, VCR Or Computer HOW to Connect Your Portable CD PlayerFollowmodes. your progress with the feedback Your CD player has only one jack, see instruction BHOW to Connect Your Portable Stereo HOW to Connect Your Home StereoPlug one end of the audio cable into the jack Audio OUT jack on your stereoHOW to Connect Your Computer HOW to Connect Your VCRAudio Cable Adapter Adapter Audio CablePressVCR. the play button on your CD player or ProgramsCD PLAYER, VCR, or Computer on Return to the elliptical crosstrainer and begin Exercising HOW to USE Programs Directly from OUR WEB SiteFollowprogram.the on-line instructions to start Battery Replacement HOW to Level the Elliptical CrosstrainerHandgrip Pulse Sensor Troubleshooting HOW to Move the Elliptical CrosstrainerConditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyR0902A DescriptionR0902A 8818HOW to Order Replacement Parts Limited Warranty860 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT