PART | R0904A |
To locate the parts listed below, see the EXPLODED DRAWING on pages 26 and 27.
Key No. | Qty. | Description | Key No. | Qty. | Description |
1 | 1 | Frame | 53 | 1 | Reed Switch Bracket |
2 | 1 | Upright | 54 | 1 | Clamp |
3 | 1 | Ramp | 55 | 1 | Reed Switch/Wire |
4 | 1 | Left Pedal Leg | 56 | 1 | Return Spring |
5 | 1 | Right Pedal Leg | 57 | 3 | M10 Split Washer |
6 | 1 | Rear Stabilizer | 58 | 1 | Resistance Cable |
7 | 2 | Rear Stabilizer Endcap | 59 | 1 | Flywheel Axle |
8 | 1 | Front Stabilizer | 60 | 2 | Flywheel Bearing |
9 | 2 | Front Stabilizer Endcap | 61 | 1 | Eye Bolt |
10 | 1 | Left Pedal | 62 | 1 | Adjustment Bracket |
11 | 1 | Right Pedal | 63 | 2 | M10 x 92mm Carriage Bolt |
12 | 1 | Incline Motor | 64 | 2 | M6 Washer |
13 | 1 | Incline Axle | 65 | 2 | M8 x 63mm Bolt Set |
14 | 1 | Pivot Axle | 66 | 2 | M8 Washer |
15 | 1 | Left Side Shield | 67 | 2 | M10 x 60mm Button Bolt |
16 | 1 | Right Side Shield | 68 | 2 | Handlebar Bushing |
17 | 1 | Console | 69 | 4 | M5 x 25mm Screw |
18 | 2 | Flywheel Cover | 70 | 1 | Stop Bolt |
19 | 1 | Arm Axle | 71 | 2 | Flywheel Washer |
20 | 2 | Pulse Sensor w/Wire | 72 | 1 | M10 x 68mm Button Bolt |
21 | 1 | Right Incline Cover | 73 | 2 | Pedal Leg Spacer |
22 | 1 | Left Incline Cover | 74 | 1 | Idler Screw |
23 | 1 | Right Handlebar | 75 | 1 | Stop Bracket |
24 | 1 | Left Handlebar | 76 | 4 | M6 x 16mm Patch Screw |
25 | 1 | Handlebar Cover | 77 | 2 | M6 Nut |
26 | 2 | Axle Cover | 78 | 4 | M5 x 12mm Bolt |
27 | 1 | 79 | 4 | M5 Washer | |
28 | 2 | Pedal Wheel | 80 | 2 | M5 x 6mm Screw |
29 | 4 | Wheel Bearing | 81 | 6 | Upper Body Bushing |
30 | 2 | Frame Bushing | 82 | 2 | 5/16” x 25mm Flange Screw |
31 | 2 | Upper Body Leg | 83 | 4 | M6 x 48mm Flat Head Screw |
32 | 1 | “C” Magnet | 84 | 2 | Upper Body Grip |
33 | 4 | Pedal Leg Cover | 85 | 4 | M8 x 42mm Button Bolt |
34 | 1 | Left Crank Arm | 86 | 6 | M8 Nylon Jam Nut |
35 | 1 | 29.5mm Pulley Spacer | 87 | 2 | Upper Body Foam Grip |
36 | 1 | Flywheel | 88 | 4 | M8 Nylon Locknut |
37 | 1 | Magnet | 89 | 8 | M10 Nylon Locknut |
38 | 1 | Pulley/Crank | 90 | 2 | Sleeve |
39 | 1 | Control Box Cover | 91 | 2 | Axle Cover Endcap |
40 | 1 | Control Board | 92 | 1 | Power Socket |
41 | 1 | Control Box | 93 | 1 | Power Cord |
42 | 1 | Lower Wire Harness | 94 | 4 | #8 x 9.5mm Screw |
43 | 1 | Plastic Washer | 95 | 1 | Upper Wire Harness |
44 | 2 | Crank Bearing | 96 | 1 | M4 x 16mm Round Head Screw |
45 | 1 | Idler | 97 | 7 | M5 x 16mm Screw |
46 | 2 | Foot | 98 | 16 | M4 x 16mm Screw |
47 | 4 | Ramp Bushing | 99 | 2 | Ramp Spacer |
48 | 2 | Ramp Cover | 100 | 4 | M5 Nylon Locknut |
49 | 1 | Incline Sensor | 101 | 1 | Pulse Extension Wire |
50 | 1 | Sensor Cover | 102 | 1 | Right Crank Arm |
51 | 2 | Pedal Leg Bushing | 103 | 1 | M6 Nylon Locknut |
52 | 1 | Resistance Motor | 104 | 1 | Belt |
24