Precor P10 Commercial Cardiovascular Equipment Limited Warranty, Warranty Periods and Coverage

Page 107

Chapter 5

Commercial Cardiovascular Equipment Limited Warranty

PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS.

Limited Warranty.

Precor Incorporated warrants all new Precor products to be free from defects in materials and manufacture for the warranty periods set forth below. The warranty periods commence on the invoice date of the original purchase. This warranty applies only against defects discovered within the warranty period and extends only to the original purchaser of the product. Parts repaired or replaced under the terms of this warranty will be warranted for the remainder of the original warranty period only. To claim under this warranty, the buyer must notify Precor or your authorized Precor dealer within 30 days after the date of discovery of any nonconformity and make the affected product available for inspection by Precor or its service representative. Precor’s obligations under this warranty are limited as set forth below.

Warranty Periods and Coverage.

All Commercial Cardiovascular Products (excluding StretchTrainer, Strength Products, and coverage specific to certain models and options as defined below):

Frame: 7 years

Treadmill drive motor: 5 years

Items subject to wear: 1 year

All other parts (including mechanical parts and electronic parts): 2 years

Labor: 1 year

880 Line Commercial Cardiovascular Products (superseding the coverage above where applicable):

Labor on the P80 console: 2 years

High wear items on the P80 console, including headphone jack, USB connector, and iPod® connector: 90 days

Image 107
Contents Operating and Maintaining the P10 Console Page Page Intellectual Property Notice Edition InformationTrademark Note Safety Precautions Important Safety InstructionsOperating and Maintaining the P10 Console Important Safety Instructions Operating and Maintaining the P10 Console Product Recycling and Disposal Hazardous Materials and Proper DisposalRadio Frequency Interference RFI Safety Approvals for Cardiovascular EquipmentRegulatory Notices for Cardiovascular Exercise Equipment Cardiovascular Type EquipmentDébranchez avant de réparer Industry CanadaEuropean Applications Electrical Recommendations 120 V and 240 V Treadmills North American 120-volt, 20-amp power receptacleIEC-320 C13 and C14 plugs Obtaining ServiceOperating and Maintaining the P10 Console Table of Contents Operating and Maintaining the P10 Console Getting Started Activating the Console for Self-Powered EquipmentActivating the Console for Self-Powered Equipment Optional Use of the Power Adapter P10 console keys Parts of the console Number Name Details Identifying Parts of the ConsoleNumber Name Details System Settings Setting Up the ConsoleClub Parameters Safety Code Treadmill onlyTo view the Club Settings Navigational keys for the system setting modes Key FunctionSet Max Pause Time All Equipment Select Language All EquipmentSet Units All Equipment Set Max Workout Time All EquipmentHidden Programs Treadmill only Set Cool Down Time All EquipmentSet Speed Limit Treadmill only Set Incline Limit Treadmill onlySet Resistance Range Bike only Remote Speed Control Treadmill onlySet Auto Stop Treadmill only Set Crossramp Auto-level EFX onlyViewing the Informational Displays To view the System settingsHour Meter Product Value Information providedEvent Error Log Event Description of Event Number User ID Entry with Csafe Equipment Csafe access keys Keys FunctionIntroducing Users to the P10 Console Using the Touch Heart Rate FeatureHeart rate target zones To use a chest strap transmitter Using a Chest Strap TransmitterRestart switch Using the Treadmill Safety ClipAttaching the safety clip Treadmill Auto Stop Automatic Stop Function  Press Quick Start Starting a WorkoutPaused Externally Powered Equipment Starting a Preset Programmed WorkoutPausing and Resuming an Exercise Session Pending Shutdown Self-Powered Equipment Ending a Session To remove dust and dirt from the console MaintenanceCleaning the Console and Display Changing the Belt Newer Model AMT Only Page Precor Incorporated Assembling and Maintaining TRM 800-Series Treadmills Page Page Assembling and Maintaining TRM 800-SERIES Treadmills Important Safety Instructions Assembling and Maintaining TRM 800-Series Treadmills Important Safety Instructions 19.7 in. behind or in front the machine Safety Code Educating Users Regulatory Notices for the Rfid Module Radio Frequency Interference RFI PVS and P80 Regulatory Notice Federal Communications Commission, Part Industry Canada Treadmill Grounding Instructions Obtaining Service Obtaining Updated Documentation Checking Treadmill Alignment and Adjusting Commercial Cardiovascular Equipment Limited Warranty Assembling the Treadmill To prepare the treadmill for assemblyRequired Tools Installation RequirementsFasteners Hardware Kit not to scaleTo unpack the cables Unpacking the CablesRemoval and replacement of the rear fairing cover Assembling the Frame To begin assembly of the frameUpright support attachment, right side Blank plate removal Cable connections and mounting points in the treadmill base To thread cables through the framePoint Component Appearance Already Lower InstalledCable connections and mounting points Upright support attachment, left side To secure the fasteners Completing AssemblyTo complete assembly of the treadmill base Checking Treadmill Alignment and Adjusting the Running BeltTo level the treadmill Leveling the UnitLeveling foot adjustment Plugging In the Power CordBreaking in the Equipment Installing the Console To thread the cable assembly Threading the Cable Assembly P80Console positioning on base unit Cable connections, P80 console Connecting Cables P80Location Connecting the Television CableP80 internal cable connections Cable Connector Type Circuit To connect the television cableConnecting the television cable Connecting the Ethernet and base unit data cables Connecting the Ethernet and Base Unit Data CablesConnecting the heart rate cable Connecting the Heart Rate Sensor CableConnecting the power cable Connecting the Power CableTo complete the installation Completing the Console Installation P80Threading the Cable Assembly P30 and P10 Cable positioning Cable routing from the mount into the console Connecting Cables P30 and P10Cable connections, P30 and P10 consoles P30 and P10 internal cable connections Completing the Console Installation P30 and P10Cable Connector Type Circuit Location To reassemble the fairing Reassembling the Treadmill FairingTo verify that the heart rate display is operational Verifying That the Heart Rate Display Is OperationalDaily Cleaning Daily Inspection Monthly Maintenance Weekly MaintenanceTo check the alignment of the running belt Checking the Alignment of the Running BeltTo adjust the running belt Adjusting the Running BeltStoring the Chest Strap To put the treadmill into an inclined position for moving Moving the EquipmentLong-Term Storage To enter the safety code and start the treadmill Treadmill Safety FeaturesEntering the Safety Code Using the Treadmill Safety Clip Turning the Treadmill On and Off Weight LimitLocation Warranty Periods and Coverage Commercial Cardiovascular Equipment Limited WarrantyLimited Warranty Conditions and Restrictions Exclusive Remedies Complete this portion and keep for your records Exclusion of Consequential and Incidental DamagesPage TRM 800-Series PAG/OM 300713-401 rev J