Precor P10 manual Important Safety Instructions

Page 7

Important Safety Instructions

5

Read, understand, and test the emergency stop procedures before use.

Keep the power cord or optional power adapter and plug away from heated surfaces.

Route power cables so that they are not walked on, pinched, or damaged by items placed upon or against them, including the equipment itself.

Ensure the equipment has adequate ventilation. Do not place anything on top of or over the equipment. Do not use on a cushioned surface that could block the ventilation opening.

Assemble and operate the equipment on a solid, level surface.

SPACING—The below minimum spacing recommendations are based on a combination of the ASTM (U.S.) voluntary standards and EN (European) regulations as of October 1, 2012, for access, passage around, and emergency dismount:

Treadmills—a minimum of 0.5 m (19.7 in.) on each side of the treadmill and 2 m (78 in.) behind the machine.

Cardio equipment other than treadmills—a minimum of 0.5 m (19.7 in.) on at least one side, and 0.5 m (19.7 in.) behind or in front the machine.

Careful consideration should be given to the requirements of the Americans with Disabilities Act (ADA), US Code 28 CFR (see Section 305). ASTM standards are voluntary and may not reflect current industry standards. The actual area for access, passage around, and emergency dismount is the responsibility of the facility. The facility should consider the total space requirements for training on each unit, voluntary and industry standards, and any local, state, and federal regulations. Standards and regulations are subject to change at any time.

Important: These spacing recommendations should be used when positioning equipment away from sources of heat, such as radiators, heat registers, and stoves. Avoid temperature extremes.

Keep equipment away from water and moisture. Avoid dropping anything on or spilling anything inside the equipment to prevent electric shock or damage to the electronics.

Image 7
Contents Operating and Maintaining the P10 Console Page Page Trademark Note Edition Information Intellectual Property Notice Safety Precautions Important Safety InstructionsOperating and Maintaining the P10 Console Important Safety Instructions Operating and Maintaining the P10 Console Product Recycling and Disposal Hazardous Materials and Proper DisposalRadio Frequency Interference RFI Safety Approvals for Cardiovascular EquipmentRegulatory Notices for Cardiovascular Exercise Equipment Cardiovascular Type EquipmentEuropean Applications Industry CanadaDébranchez avant de réparer Electrical Recommendations 120 V and 240 V Treadmills North American 120-volt, 20-amp power receptacleIEC-320 C13 and C14 plugs Obtaining ServiceOperating and Maintaining the P10 Console Table of Contents Operating and Maintaining the P10 Console Activating the Console for Self-Powered Equipment Activating the Console for Self-Powered EquipmentGetting Started Optional Use of the Power Adapter P10 console keys Parts of the console Number Name Details Identifying Parts of the ConsoleNumber Name Details System Settings Setting Up the ConsoleClub Parameters Safety Code Treadmill onlyTo view the Club Settings Navigational keys for the system setting modes Key FunctionSet Max Pause Time All Equipment Select Language All EquipmentSet Units All Equipment Set Max Workout Time All EquipmentHidden Programs Treadmill only Set Cool Down Time All EquipmentSet Speed Limit Treadmill only Set Incline Limit Treadmill onlySet Resistance Range Bike only Remote Speed Control Treadmill onlySet Auto Stop Treadmill only Set Crossramp Auto-level EFX onlyViewing the Informational Displays To view the System settingsHour Meter Product Value Information providedEvent Error Log Event Description of Event Number User ID Entry with Csafe Equipment Csafe access keys Keys FunctionIntroducing Users to the P10 Console Using the Touch Heart Rate FeatureHeart rate target zones To use a chest strap transmitter Using a Chest Strap TransmitterRestart switch Using the Treadmill Safety ClipAttaching the safety clip Treadmill Auto Stop Automatic Stop Function  Press Quick Start Starting a WorkoutPausing and Resuming an Exercise Session Starting a Preset Programmed WorkoutPaused Externally Powered Equipment Pending Shutdown Self-Powered Equipment Ending a Session Cleaning the Console and Display MaintenanceTo remove dust and dirt from the console Changing the Belt Newer Model AMT Only Page Precor Incorporated Assembling and Maintaining TRM 800-Series Treadmills Page Page Assembling and Maintaining TRM 800-SERIES Treadmills Important Safety Instructions Assembling and Maintaining TRM 800-Series Treadmills Important Safety Instructions 19.7 in. behind or in front the machine Safety Code Educating Users Regulatory Notices for the Rfid Module Radio Frequency Interference RFI PVS and P80 Regulatory Notice Federal Communications Commission, Part Industry Canada Treadmill Grounding Instructions Obtaining Service Obtaining Updated Documentation Checking Treadmill Alignment and Adjusting Commercial Cardiovascular Equipment Limited Warranty Assembling the Treadmill To prepare the treadmill for assemblyRequired Tools Installation RequirementsFasteners Hardware Kit not to scaleTo unpack the cables Unpacking the CablesRemoval and replacement of the rear fairing cover Assembling the Frame To begin assembly of the frameUpright support attachment, right side Blank plate removal Cable connections and mounting points in the treadmill base To thread cables through the frameCable connections and mounting points Component Appearance Already Lower InstalledPoint Upright support attachment, left side To secure the fasteners Completing AssemblyTo complete assembly of the treadmill base Checking Treadmill Alignment and Adjusting the Running BeltTo level the treadmill Leveling the UnitLeveling foot adjustment Plugging In the Power CordBreaking in the Equipment Installing the Console To thread the cable assembly Threading the Cable Assembly P80Console positioning on base unit Cable connections, P80 console Connecting Cables P80Location Connecting the Television CableP80 internal cable connections Cable Connector Type Circuit To connect the television cableConnecting the television cable Connecting the Ethernet and base unit data cables Connecting the Ethernet and Base Unit Data CablesConnecting the heart rate cable Connecting the Heart Rate Sensor CableConnecting the power cable Connecting the Power CableThreading the Cable Assembly P30 and P10 Completing the Console Installation P80To complete the installation Cable positioning Cable routing from the mount into the console Connecting Cables P30 and P10Cable connections, P30 and P10 consoles Cable Connector Type Circuit Location Completing the Console Installation P30 and P10P30 and P10 internal cable connections To reassemble the fairing Reassembling the Treadmill FairingTo verify that the heart rate display is operational Verifying That the Heart Rate Display Is OperationalDaily Cleaning Daily Inspection Monthly Maintenance Weekly MaintenanceTo check the alignment of the running belt Checking the Alignment of the Running BeltTo adjust the running belt Adjusting the Running BeltStoring the Chest Strap To put the treadmill into an inclined position for moving Moving the EquipmentLong-Term Storage Entering the Safety Code Treadmill Safety FeaturesTo enter the safety code and start the treadmill Using the Treadmill Safety Clip Turning the Treadmill On and Off Weight LimitLocation Limited Warranty Commercial Cardiovascular Equipment Limited WarrantyWarranty Periods and Coverage Conditions and Restrictions Exclusive Remedies Complete this portion and keep for your records Exclusion of Consequential and Incidental DamagesPage TRM 800-Series PAG/OM 300713-401 rev J