Precor P10 manual Setting Up the Console, System Settings

Page 21

Chapter 2

Setting Up the Console

Use the System mode to configure settings in ways that benefit your users and your facility. The System menu is visible only to administrators and registered service technicians. Changes made to these settings are saved to the fitness equipment.

The System Settings categories are:

Club Parameters

Informational Display

System Settings

System Setting features remain hidden from club patrons and can only be accessed using special keypresses. To view the System Settings, the equipment must be in the Welcome state. The equipment is in the Welcome state when it is on, but not actually in use. This means that there is no exercise session, data entry, or diagnostic operation in progress.

When the equipment is in the Welcome state:

SELECT A WORKOUT OR PRESS QUICKSTART TO BEGIN scrolls in the text display.

On the treadmill, the belt is not moving and the lift motor is off.

Note: On self-powered equipment, the console initializes when you begin working out. You must maintain a minimum rate of motion for the Welcome banner to appear.

The changes made in System Setting modes become the default settings when the display resets to the Welcome banner.

CAUTION: If you change the Unit of Measure display on the treadmill, check the speed setting to verify that it is correct.

Image 21

Contents Operating and Maintaining the P10 Console Page Page Edition Information Trademark NoteIntellectual Property Notice Safety Precautions Important Safety InstructionsOperating and Maintaining the P10 Console Important Safety Instructions Operating and Maintaining the P10 Console Product Recycling and Disposal Hazardous Materials and Proper DisposalRegulatory Notices for Cardiovascular Exercise Equipment Safety Approvals for Cardiovascular EquipmentCardiovascular Type Equipment Radio Frequency Interference RFIIndustry Canada European ApplicationsDébranchez avant de réparer Electrical Recommendations 120 V and 240 V Treadmills North American 120-volt, 20-amp power receptacleIEC-320 C13 and C14 plugs Obtaining ServiceOperating and Maintaining the P10 Console Table of Contents Operating and Maintaining the P10 Console Activating the Console for Self-Powered Equipment Activating the Console for Self-Powered EquipmentGetting Started Optional Use of the Power Adapter P10 console keys Parts of the console Number Name Details Identifying Parts of the ConsoleNumber Name Details System Settings Setting Up the ConsoleTo view the Club Settings Safety Code Treadmill onlyNavigational keys for the system setting modes Key Function Club ParametersSet Units All Equipment Select Language All EquipmentSet Max Workout Time All Equipment Set Max Pause Time All EquipmentSet Speed Limit Treadmill only Set Cool Down Time All EquipmentSet Incline Limit Treadmill only Hidden Programs Treadmill onlySet Auto Stop Treadmill only Remote Speed Control Treadmill onlySet Crossramp Auto-level EFX only Set Resistance Range Bike onlyViewing the Informational Displays To view the System settingsHour Meter Product Value Information providedEvent Error Log Event Description of Event Number User ID Entry with Csafe Equipment Csafe access keys Keys FunctionIntroducing Users to the P10 Console Using the Touch Heart Rate FeatureHeart rate target zones To use a chest strap transmitter Using a Chest Strap TransmitterRestart switch Using the Treadmill Safety ClipAttaching the safety clip Treadmill Auto Stop Automatic Stop Function  Press Quick Start Starting a WorkoutStarting a Preset Programmed Workout Pausing and Resuming an Exercise SessionPaused Externally Powered Equipment Pending Shutdown Self-Powered Equipment Ending a Session Maintenance Cleaning the Console and DisplayTo remove dust and dirt from the console Changing the Belt Newer Model AMT Only Page Precor Incorporated Assembling and Maintaining TRM 800-Series Treadmills Page Page Assembling and Maintaining TRM 800-SERIES Treadmills Important Safety Instructions Assembling and Maintaining TRM 800-Series Treadmills Important Safety Instructions 19.7 in. behind or in front the machine Safety Code Educating Users Regulatory Notices for the Rfid Module Radio Frequency Interference RFI PVS and P80 Regulatory Notice Federal Communications Commission, Part Industry Canada Treadmill Grounding Instructions Obtaining Service Obtaining Updated Documentation Checking Treadmill Alignment and Adjusting Commercial Cardiovascular Equipment Limited Warranty Assembling the Treadmill To prepare the treadmill for assemblyRequired Tools Installation RequirementsFasteners Hardware Kit not to scaleTo unpack the cables Unpacking the CablesRemoval and replacement of the rear fairing cover Assembling the Frame To begin assembly of the frameUpright support attachment, right side Blank plate removal Cable connections and mounting points in the treadmill base To thread cables through the frameComponent Appearance Already Lower Installed Cable connections and mounting pointsPoint Upright support attachment, left side To secure the fasteners Completing AssemblyTo complete assembly of the treadmill base Checking Treadmill Alignment and Adjusting the Running BeltTo level the treadmill Leveling the UnitLeveling foot adjustment Plugging In the Power CordBreaking in the Equipment Installing the Console To thread the cable assembly Threading the Cable Assembly P80Console positioning on base unit Cable connections, P80 console Connecting Cables P80P80 internal cable connections Cable Connector Type Circuit Connecting the Television CableTo connect the television cable LocationConnecting the television cable Connecting the Ethernet and base unit data cables Connecting the Ethernet and Base Unit Data CablesConnecting the heart rate cable Connecting the Heart Rate Sensor CableConnecting the power cable Connecting the Power CableCompleting the Console Installation P80 Threading the Cable Assembly P30 and P10To complete the installation Cable positioning Cable routing from the mount into the console Connecting Cables P30 and P10Cable connections, P30 and P10 consoles Completing the Console Installation P30 and P10 Cable Connector Type Circuit LocationP30 and P10 internal cable connections To reassemble the fairing Reassembling the Treadmill FairingTo verify that the heart rate display is operational Verifying That the Heart Rate Display Is OperationalDaily Cleaning Daily Inspection Monthly Maintenance Weekly MaintenanceTo check the alignment of the running belt Checking the Alignment of the Running BeltTo adjust the running belt Adjusting the Running BeltStoring the Chest Strap To put the treadmill into an inclined position for moving Moving the EquipmentLong-Term Storage Treadmill Safety Features Entering the Safety CodeTo enter the safety code and start the treadmill Using the Treadmill Safety Clip Turning the Treadmill On and Off Weight LimitLocation Commercial Cardiovascular Equipment Limited Warranty Limited WarrantyWarranty Periods and Coverage Conditions and Restrictions Exclusive Remedies Complete this portion and keep for your records Exclusion of Consequential and Incidental DamagesPage TRM 800-Series PAG/OM 300713-401 rev J