Precor EFX534i t owner manual Setting Up the EFX, Installation Requirements, Assembly Instructions

Page 11

C O M M E R C I A L P R O D U C T S D I V I S I O N

Setting Up the EFX ®

You do not need any special knowledge or experience to set up the EFX. However, because of the size and weight of the EFX, you will need to obtain appropriate assistance during assembly.

INSTALLATION REQUIREMENTS

Follow these installation requirements when installing the EFX. If you do not install the EFX according to the following guidelines, you could void the Precor Limited Warranty.

•Set up the EFX on a solid, flat surface. Unpack and assemble the EFX close to where you’ll use it. Make sure that the flat surface under the unit is smooth and level. A level unit is required for the user’s safety and for proper operation.

•Provide ample space around the unit. Open space around the unit makes for a safer mount and dismount.

•Fill out and mail the limited warranty card. The serial number is located on a label at the rear of the unit near the optional power adapter receptacle. Write the serial number onto the Precor Limited Warranty card found on the back cover of this manual. Refer to Obtaining Service on page 7 and write the number there as well.

ASSEMBLY INSTRUCTIONS

To assist you in the assembly, the items in the Hardware kit, shown in Diagram 3, correspond to a particular letter in the alphabet. These letters appear throughout the assembly instructions. Refer to Diagram 3 on page 10.

1.Obtain assistance. Place the shipping carton close to the location where you plan to use the unit. Break down the side walls so that they lie flat. You may need to cut the tie wraps that hold the base frame and roller arms to the pallet.

2.Unpack the EFX534i. Remove the packing materials and loose contents. Refer to the list on page 9.

3.Move the unit to the location where you plan to use it. Once you attach the handrails and base stabilizers, the EFX is difficult to move through a standard door frame. Make sure to assemble the unit where it will not have to be moved through any doorways.

CAUTION: Do not assemble the EFX if it is connected to the optional power adapter. Remove the power adapter from the EFX prior to as- sembly.

page 11

Image 11

Contents M M E R C I a L P R O D U C T S D I V I S I O N Important Safety Instructions Hazardous Materials and Proper Disposal Safety ApprovalDiagram 1 Avoid injury from the roller arm mechanism Table of Contents Back cover Changing the Display Features using the Select KeyInterval Program European Applications RFI Radio Frequency InterferenceEuropean Applications User’s authority to operate the equipmentModel number EFX534i Unit number Serial number EFX SELF-POWERED FeaturesObtaining Service Diagram 2 EFX serial number locationEquipment and prevent injuries to yourself About this ManualAcquiring the Appropriate Tools Unpacking the EFXStandard Equipment Other EquipmentHardware kit Hardware KITAssembly Instructions Setting Up the EFXInstallation Requirements Diagram Base tube Diagram 7 Connect the cablesDiagram 8 Place the base on supportive blocks Bolts G and washers H Frame stabilizer Mounting bolts Diagram 11 TightenHandlebars Protrusions Bracket Tighten bolts securely Diagram 12 SecureM M E R C I a L O D U C T S V I S I O N M M E R C I a L O D U C T S V I S I O N M M E R C I a L O D U C T S V I S I O N Bracket cover Diagram 16 SecureFoot pedal Diagram 17 Level the unitRotate rear adjustment pads Diagram 18 Clean the rampRemoving the Locking PIN Diagram 19 Insert the front end capDampen with water Testing the Heart Rate DisplayDiagram 21 Wearing the chest strap Changing the Custom Settings Custom Settings ModeDetermining the Units of Measure Electrical power must be suppliedDisplay key functions within the Custom Settings Mode Reset, Enter, QuickStart Setting a Workout Time LimitSetting a Pause Time Limit Moves the blinking LED from field to field Using Csafe Standard EquipmentEnter Reset User ID Entry Program KeysCenter Display Features on the Display ConsoleDiagram 23 EFX Display Console SmartRate display EFX534i DisplayQuickStart User Setup PromptsSetup Prompts Description SelectPrecor banner Using Quickstarttm During the Setup PromptsWeight prompt Press Quickstart Following occursCenter Display Informational Displays Prior to Shutdown Low BatterySmartrate Display Keys on the Display Console Diagram 24 Display console keypadPrompts Default Value Default ValuesExercising on the EFX Heart Rate FeatureUtilizing the Smartrate Feature Weight Loss ZoneWorkout Tips Diagram 26 Using the EFX handlebars Using the HandlebarsUsing the Stationary Handrail Changing the Display Features Using the Select KEYCarefully step down from the EFX Quick Steps to Working OUTIs detected PAUSE, Cool Down and Exit FeaturesCooling Down After a Workout A program, This is what happensPause Mode, you Press Reset Displays the Workout Summary bannerCool down Mode Inserting the Locking PINInterval Program Manual Mode and the Quickstarttm KEYPrograms Hill Climb ProgramTo use the interval program, take the following steps Diagram 27 Target ZonesCross Training Program Weight Loss ProgramInspection MaintenanceCleaning the Equipment Servicing the EFX and Long Term Storage Symptoms of a LOW BatteryUsing the Power Adapter Storing the Chest StrapPower Adapter Power Cord Replacing the BatteryM M E R C I a L P R O D U C T S D I V I S I O N Thank You and Welcome to Precor How many members do you have? Date of Purchase Purchased from Dealer nameProduct Serial Numbers Please indicate the type and number of products purchasedComplete this portion and keep for your records Limited WarrantyWarranty Periods and Coverage Conditions and RestrictionsEFX 534i Programs 5 Total EFX 534i Display Readouts Product Specifications Electronic Specifications