Precor EFX534i t owner manual Diagram

Page 12

C O M M E R C I A L P R O D U C T S D I V I S I O N

Diagram 4 Front base assembly.
Front base tube
Height adjuster
Tighten the height	1	2
adjuster so that the	1	2
nut is secure against
the front tube.

4.Thread the height adjuster to its lowest position. Diagram 4, #1 and #2. Remove the height adjuster from the Hardware kit. Ask an assistant to lift the front base tube while you insert the height adjuster.Turn the height adjuster so that the threads appear inside the base tube. Tighten the nut (with a crescent wrench) when the height adjuster is fully threaded into the front base tube.

Diagram 5	Route the cable and
	attach the display
	console to the upright
	support.
	Display console
	Cable
	Upright support
	1	2

5.Prepare for the attachment of the upright support to the base assembly. Diagrams 5 and 6. Remove the four Phillips-head screws (D), two bolts (G), and two washers (H) from the Hardware kit. Place one washer (H) on each of the two bolts (G). Keep the fasteners together.

CAUTION: Do not stretch, crimp, or damage the cable. Excess cable may be gently pushed into the base assembly. Cables damaged by improper installation will not be covered by the Precor limited warranty.

6.Route the display console cable through the upright support. Diagram 5 , #1 Remove any tape or wire ties on the cable. Have an assistant hold the upright support securely while you grasp the display console in one hand and route the cable through the upright support with the other.

7.Attach the display console. Diagram 5, #2. Use the four phillips-head screws (D) to attach the display console to the upright support. Have your assis- tant hold the upright support securely while you align the mounting holes and tighten the screws.

page 12

Image 12

Contents M M E R C I a L P R O D U C T S D I V I S I O N Important Safety Instructions Safety Approval Diagram 1 Avoid injury from the roller arm mechanismHazardous Materials and Proper Disposal Table of Contents Changing the Display Features using the Select Key Interval ProgramBack cover RFI Radio Frequency Interference European ApplicationsUser’s authority to operate the equipment European ApplicationsEFX SELF-POWERED Features Obtaining ServiceDiagram 2 EFX serial number location Model number EFX534i Unit number Serial numberAbout this Manual Equipment and prevent injuries to yourselfUnpacking the EFX Standard EquipmentOther Equipment Acquiring the Appropriate ToolsHardware KIT Hardware kitSetting Up the EFX Installation RequirementsAssembly Instructions Diagram Diagram 7 Connect the cables Base tubeDiagram 8 Place the base on supportive blocks Bolts G and washers H Frame stabilizer Diagram 11 Tighten Mounting boltsDiagram 12 Secure Handlebars Protrusions Bracket Tighten bolts securelyM M E R C I a L O D U C T S V I S I O N M M E R C I a L O D U C T S V I S I O N M M E R C I a L O D U C T S V I S I O N Diagram 16 Secure Bracket coverDiagram 17 Level the unit Rotate rear adjustment padsDiagram 18 Clean the ramp Foot pedalDiagram 19 Insert the front end cap Removing the Locking PINTesting the Heart Rate Display Diagram 21 Wearing the chest strapDampen with water Custom Settings Mode Changing the Custom SettingsElectrical power must be supplied Display key functions within the Custom Settings ModeDetermining the Units of Measure Setting a Workout Time Limit Setting a Pause Time LimitReset, Enter, QuickStart Using Csafe Standard Equipment Enter ResetUser ID Entry Program Keys Moves the blinking LED from field to fieldFeatures on the Display Console Diagram 23 EFX Display Console SmartRate displayEFX534i Display Center DisplayUser Setup Prompts Setup Prompts DescriptionSelect QuickStartUsing Quickstarttm During the Setup Prompts Weight promptPress Quickstart Following occurs Precor bannerCenter Display Low Battery Smartrate DisplayInformational Displays Prior to Shutdown Diagram 24 Display console keypad Keys on the Display ConsoleDefault Values Prompts Default ValueHeart Rate Feature Utilizing the Smartrate FeatureWeight Loss Zone Exercising on the EFXWorkout Tips Using the Handlebars Using the Stationary HandrailChanging the Display Features Using the Select KEY Diagram 26 Using the EFX handlebarsQuick Steps to Working OUT Carefully step down from the EFXPAUSE, Cool Down and Exit Features Cooling Down After a WorkoutA program, This is what happens Is detectedPress Reset Displays the Workout Summary banner Cool down ModeInserting the Locking PIN Pause Mode, youManual Mode and the Quickstarttm KEY ProgramsHill Climb Program Interval ProgramDiagram 27 Target Zones To use the interval program, take the following stepsWeight Loss Program Cross Training ProgramMaintenance Cleaning the EquipmentInspection Symptoms of a LOW Battery Using the Power AdapterStoring the Chest Strap Servicing the EFX and Long Term StorageReplacing the Battery Power Adapter Power CordM M E R C I a L P R O D U C T S D I V I S I O N Thank You and Welcome to Precor Date of Purchase Purchased from Dealer name Product Serial NumbersPlease indicate the type and number of products purchased How many members do you have?Limited Warranty Warranty Periods and CoverageConditions and Restrictions Complete this portion and keep for your recordsProduct Specifications Electronic Specifications EFX 534i Programs 5 Total EFX 534i Display Readouts