ProForm PATL40707.0 user manual Troubleshooting, Problem The power turns off during use

Page 26

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 12) If an ex- tension cord is needed, use only a 3-conductor, 1 mm2 (14-gauge) cord that is no longer than 1.5 m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the three 3/4" Screws (12) and carefully pivot the Hood (61) off.

12

61

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents QUESTIONS? Model No. PATL40707.0 Serial NoTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unpluggedPage Not fully fold the Frame yet Careful not to pinch the Upright WireFully tighten the Bolts yet Not overtighten the Nut the Wheel must turn FreelyInsert the indicated connectors into the Right Upright Be careful not to pinch the wires Pull on the sleeve to make sure that it is locked into placeRaise the Frame 56 to the position shown PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleSelect the user mode HOW to Turn on the PowerHOW to Personalize Console Settings Set the date and time Select a default user settingHOW to Identify Yourself AS User 1 or User HOW to USE the Manual Mode HOW to USE a Preset Workout or a Weight Loss Workout Press the Start button to start the workout HOW to Create a Learn Workout Select a learn workoutHOW to USE a Learn Workout Change the workout if desired HOW to View the Fitness Journal Exit the user mode HOW to Reset the Fitness JournalSelect the user mode. See on Reset the fitness journal Information ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyR0907A Key No. Qty DescriptionQty R1207B Exploded Drawing B-Model No. PATL40707.0 Exploded Drawing C-Model No. PATL40707.0 Exploded Drawing D-Model No. PATL40707.0 Icon Authorized Dealer Ordering Replacement PartsLimited Warranty
Top Page Image Contents