JVC RX-6018VBK manual Press SURROUND MODE, repeatedly until “THEATER”, appears on the display

JVC Theater Surround adjustments

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 12).

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

•You cannot adjust the rear speaker output levels when you have set “REAR SPK” to “NO.” See page 12.

•You cannot adjust the center speaker output level when you have set “CENTER SPK” to “NO.” See page 12.

From the remote control:

1. Press SURROUND MODE	SURROUND
repeatedly until “THEATER”
appears on the display.	SURROUND
	MODE
The PRO LOGIC and DSP indicators also
light up on the display.

6. Press EFFECT to select an effect				EFFECT
				4
level you want.
• Each time you press the button, the effect
level changes as follows:
DSP EFFECT 1	DSP EFFECT 2		DSP EFFECT 3
DSP EFFECT 5		DSP EFFECT 4

As the number increases, JVC Theater Surround becomes stronger (normally set it to “DSP EFFECT 3”).

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

2. Press SOUND.					SOUND
	The 10 keys are activated for sound adjustments.
3. Press TEST to check the speaker					TEST
					1
	output balance.
	“TEST TONE L” starts flashing on the
	display, and a test tone comes out of the
	speakers in the following order:
	TEST TONE L		TEST TONE C		TEST TONE R
	(Left front speaker)		(Center speaker)		(Right front speaker)
		TEST TONE LS		TEST TONE RS
		(Left rear speaker)		(Right rear speaker)

Notes:

•You can adjust the speaker output levels without outputting the test tone.

•No test tone comes out of the center speaker when “CENTER SPK” is set to “NO” (see page 12).

•No test tone comes out of the rear speakers when “REAR SPK” is set to “NO” (see page 12).

1.Press DSP MODE repeatedly until “THEATER” appears on the

display.

The PRO LOGIC and DSP indicators also light up on the display.

2.Adjust the speaker output levels.

1)Press ADJUST repeatedly until one of the following indications appears on the display.

“CENTER LEVEL”:

To adjust the center speaker level. “REAR L LEVEL”:

To adjust the left rear speaker level. “REAR R LEVEL”:

To adjust the right rear speaker level.

2)Press CONTROL UP 5/DOWN °to adjust the selected speaker output level (from +10 dB to –10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

DSP MODE

ADJUST SETTING

CONTROL

DOWN UP

3. Adjust the effect level.

1) Press ADJUST repeatedly until “DSP

ADJUST SETTIN

4.Adjust the speaker output levels.

•To adjust the center speaker level, press CENTER +/– (from +10 dB to –10 dB).

•To adjust the left rear speaker level, press REAR•L +/– (from +10 dB to –10 dB).

•To adjust the right rear speaker level, press REAR•R +/– (from +10 dB to –10 dB).

– CENTER +

5 6

–REAR•L +

8 9

MENU

EFFECT” appears on the display.

The display changes to show the current

setting.

2) Press CONTROL UP 5/DOWN °to

select the effect level.

• Each time you press the button, the

effect level changes as follows:

CONTROL

DOWN UP

– REAR•R +

10 +10

ENTER

5. Press TEST again to stop the test tone.	TEST
	1

DSP EFFECT 1DSP EFFECT 2 DSP EFFECT 3

DSP EFFECT 5 DSP EFFECT 4

As the number increases, JVC Theater Surround becomes stronger (normally set it to “DSP EFFECT 3”).

22