JVC RX-6018VBK manual Adjusting the DAP Modes, on the display

Page 26
Adjusting the DAP Modes

Adjusting the DAP Modes

Once you have adjusted the DAP modes, the adjustment is memorized for each DAP mode.

Before you start, remember...

Make sure that you have set the speaker information correctly

(see page 12).

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

• You cannot adjust the rear speaker output level when you have set

From the remote control:

1.Press SURROUND MODE repeatedly until the DAP mode —

LIVE CLUB, DANCE CLUB, HALL, or PAVILION — appears

on the display.

The DSP indicator also lights up on the display.

SURROUND

SURROUND

MODE

“REAR SPK” to “NO.” See page 12.

On the front panel:

1. Press DSP MODE repeatedly until

DSP MODE

 

the DAP mode — LIVE CLUB,

 

DANCE CLUB, HALL, or

 

PAVILION — appears on the

 

display.

 

The DSP indicator also lights up on the display.

2. Adjust the rear speaker output levels.

2. Press SOUND.

The 10 keys are activated for sound adjustments.

3. Adjust the rear speaker output

levels.

• To adjust the left rear speaker level, press

REAR•L +/– (from +10 dB to –10 dB).

• To adjust the right rear speaker level, press

REAR•R +/– (from +10 dB to –10 dB).

SOUND

– REAR•L +

8 Manual backgroundManual backgroundManual backgroundManual backgroundManual background 9

MENU

– REAR•R +

10 Manual backgroundManual backgroundManual backgroundManual backgroundManual background +10

ENTER

1)

Press ADJUST repeatedly until one of

 

the following indications appears on

 

the display.

 

“REAR L LEVEL”:

 

To adjust the left rear speaker level.

 

“REAR R LEVEL”:

 

To adjust the right rear speaker level.

2)

Press CONTROL UP 5/DOWN ° to

 

adjust the selected speaker output level

ADJUST SETTIN

CONTROL

DOWN UP

4. Press EFFECT to select an effect

level you want.

• Each time you press the button, the effect

level changes as follows:

EFFECT

4Manual background

(from +10 dB to –10 dB).

3) Repeat 1) and 2) to adjust the other

speaker output level.

Manual background DSP EFFECT 1 Manual backgroundDSP EFFECT 2 Manual backgroundDSP EFFECT 3

DSP EFFECT 5

DSP EFFECT 4

As the number increases, the selected DAP mode becomes

3.Adjust the effect level.

1)Press ADJUST repeatedly until “DSP EFFECT” appears on the display. The display changes to show the current setting.

2)Press CONTROL UP 5/DOWN ° to select the effect level.

Each time you press the button, the effect level changes as follows:

ADJUST SETTIN

CONTROL

DOWN UP

stronger (normally set it to “DSP EFFECT 3”).

Manual background DSP EFFECT 1 Manual backgroundManual backgroundDSP EFFECT 2 Manual backgroundManual backgroundDSP EFFECT 3 Manual background

DSP EFFECT 5

DSP EFFECT 4

As the number increases, the selected DAP mode becomes stronger (normally set it to “DSP EFFECT 3”).

23

Image 26
Contents AUDIO/VIDEO CONTROL RECEIVER POWERRX-6010VBK / RX-6018VBK INSTRUCTIONSWarnings, Cautions and Others Caution --POWER switchAttention --Commutateur POWER WARNING TO REDUCE THE RISK OF FIREFor U.S.A For Canada/pour Le CanadaFor Canada/pour le Canada Caution Proper VentilationUsing the DSP Modes Table of ContentsBasic Settings COMPU LINK Remote Control Systemq w e r t y Parts IdentificationRemote Control 1 2 3 4 5 6 7 8 9 pConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure Connecting the rear and center speakersPowered subwoofer Connecting Audio/Video ComponentsConnecting the subwoofer speaker Audio component connectionsTo audio Video component connectionsDVD player outputDigital connections Connecting the Power CordPutting Batteries in the Remote Control CAUTIONSS.WFR LFE LS S RS Turning the Power On and Off StandbyBasic Operations From the remote controlAdjusting the Volume Listening Only with HeadphonesMuting the Sound From the remote controlAttenuating the Input Signal Adjusting the Subwoofer Output LevelAdjusting the Tone Adjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information Recording a SourceSetting the Speakers for the DSP Modes 1. Press SETTING repeatedly until1. Press SETTING repeatedly until 1. Press SETTING repeatedly until Digital Input DIGITAL IN Terminal SettingSelecting the Analog or Digital Input Mode From the remote control ONLY Storing the Basic Settings and AdjustmentsUsing the Sleep Timer From the remote controlReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Selecting the FM Reception Mode To tune in a preset stationFrom the remote control On the front panelSurround modes Using the DSP ModesWhat are the DSP Modes? Dolby Surround Dolby Digital and Dolby Pro LogicAvailable DSP modes according to the input mode Reproducing the Sound FieldDAP modes By pressing SURROUND MODE Available DSP modesBy pressing DSP MODE To activate the SurroundAdjusting the Surround Modes 5.Adjust the speaker output levelsappears on the display 1. Press SURROUND MODErepeatedly until “THEATER” JVC Theater Surround adjustmentsAdjusting the DAP Modes on the displayActivating the DSP Modes 1. Press SURROUND ON/OFFSynchronized Recording COMPU LINK Remote Control SystemAutomatic Source Selection Tuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierCassette deck Operating Video ComponentsCD changer CD recorderSOLUTION TroubleshootingPROBLEM POSSIBLE CAUSE40 Hz to 20 kHz with no more than 0.8% total Specifications100 W per channel, min. RMS, driven into 8 Ω harmonic distortionGeneral FM tuner IHFAM tuner QUALITYSERVICE JVC SERVICE & ENGINEERING COMPANY OF AMERICAHOW TO LOCATE YOUR JVC SERVICE CENTER FACTORY SERVICE CENTER LOCATIONSLIMITED WARRANTY AUDIO-2 0101NHMMDWJEIN VICTOR COMPANY OF JAPAN, LIMITED