JVC RX-6018VBK manual Receiving Radio Broadcasts, Tuning in Stations Manually, Using Preset Tuning

Page 19
 Receiving Radio Broadcasts

Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio Broadcasts

You can browse through all the stations or use the preset function to go immediately to a particular station.

Tuning in Stations Manually

On the front panel ONLY:

1. Press FM/AM to select the band

FM/AM

(FM or AM).

Each time you press the button, the band alternates between FM and AM.

 

SPK

 

 

 

ANALOG

L

R

TUNED

VOLUME

2. Press FM/AM TUNING 5/ °

FM/AM TUNING

 

until you find the frequency you

 

want.

 

• Pressing FM/AM TUNING 5increases the frequency.

Pressing FM/AM TUNING °decreases the frequency.

Notes:

When you hold FM/AM TUNING 5/ ° in step 2, the frequency keeps changing until a station is tuned in.

When a station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display.

When an FM stereo program is received, the STEREO indicator also lights up.

Using Preset Tuning

Once a station is assigned to a channel number, the station can be quickly tuned. You can preset up to 30 FM and 15 AM stations.

To store the preset stations

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Tune in the station you want to preset (see “Tuning in Stations Manually”).

If you want to store the FM reception mode for this station, select the FM reception mode you want. See “Selecting the FM Reception Mode” on page 17.

2. Press MEMORY.

 

MEMORY

 

 

SPK

 

 

ANALOG L R

TUNED

VOLUME

CH- Manual backgroundManual background

“CH-” appears and the channel number position starts flashing on the display for about 5 seconds.

3. Press FM/AM PRESET 5/ °to

FM/AM PRESET

 

 

select a channel number while the

 

channel number position is

 

flashing.

 

 

SPK

 

 

ANALOG L R

TUNED

VOLUME

CH-

 

 

Note:

You can use the 10 keys on the remote control to select the preset number. When using the 10 keys, be sure that they are activated for the tuner, not for the CD and others. (See page 26.)

4. Press MEMORY again while the

MEMORY

 

selected channel number is flashing

 

on the display.

 

The selected channel number stops flashing.

The station is assigned to the selected channel number.

SPK

ANALOG

L

R

TUNED

VOLUME

CH-

5.Repeat steps 1 to 4 until you store all the stations you want.

To erase a stored preset station

Storing a new station on a used number erases the previously stored one.

SPK

ANALOG

L

R

TUNED

VOLUME

16

Image 19
Contents INSTRUCTIONS POWERRX-6010VBK / RX-6018VBK AUDIO/VIDEO CONTROL RECEIVERWARNING TO REDUCE THE RISK OF FIRE Caution --POWER switchAttention --Commutateur POWER Warnings, Cautions and OthersCaution Proper Ventilation For Canada/pour Le CanadaFor Canada/pour le Canada For U.S.ACOMPU LINK Remote Control System Table of ContentsBasic Settings Using the DSP Modes1 2 3 4 5 6 7 8 9 p Parts IdentificationRemote Control q w e r t yGetting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM AntennasConnecting the rear and center speakers Connecting the SpeakersBasic connecting procedure Connecting the front speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker Powered subwooferoutput Video component connectionsDVD player To audioCAUTIONS Connecting the Power CordPutting Batteries in the Remote Control Digital connectionsFrom the remote control Turning the Power On and Off StandbyBasic Operations S.WFR LFE LS S RSFrom the remote control Listening Only with HeadphonesMuting the Sound Adjusting the VolumeAdjusting the Tone Adjusting the Subwoofer Output LevelAttenuating the Input Signal Recording a Source Basic SettingsSetting the Subwoofer Information Adjusting the Front Speaker Output Balance1. Press SETTING repeatedly until Setting the Speakers for the DSP Modes1. Press SETTING repeatedly until Selecting the Analog or Digital Input Mode Digital Input DIGITAL IN Terminal Setting1. Press SETTING repeatedly until From the remote control Storing the Basic Settings and AdjustmentsUsing the Sleep Timer From the remote control ONLYUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts On the front panel To tune in a preset stationFrom the remote control Selecting the FM Reception ModeDolby Surround Dolby Digital and Dolby Pro Logic Using the DSP ModesWhat are the DSP Modes? Surround modesDAP modes Reproducing the Sound FieldAvailable DSP modes according to the input mode To activate the Surround Available DSP modesBy pressing DSP MODE By pressing SURROUND MODE5.Adjust the speaker output levels Adjusting the Surround ModesJVC Theater Surround adjustments 1. Press SURROUND MODErepeatedly until “THEATER” appears on the displayon the display Adjusting the DAP Modes1. Press SURROUND ON/OFF Activating the DSP ModesAutomatic Source Selection COMPU LINK Remote Control SystemSynchronized Recording Sound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder Operating Video ComponentsCD changer Cassette deckPOSSIBLE CAUSE TroubleshootingPROBLEM SOLUTIONharmonic distortion Specifications100 W per channel, min. RMS, driven into 8 Ω 40 Hz to 20 kHz with no more than 0.8% totalAM tuner FM tuner IHFGeneral FACTORY SERVICE CENTER LOCATIONS JVC SERVICE & ENGINEERING COMPANY OF AMERICAHOW TO LOCATE YOUR JVC SERVICE CENTER QUALITYSERVICELIMITED WARRANTY AUDIO-2 VICTOR COMPANY OF JAPAN, LIMITED 0101NHMMDWJEIN