JVC RX-6018VBK manual Connecting the Speakers, AM Antenna Connections, Basic connecting procedure

Page 7
AM Antenna Connections

AM Antenna Connections

 

 

 

 

Snap the tabs on the loop into the

ANTENNA

 

slots of the base to assemble the

 

 

FM 75

 

 

AM loop.

 

 

COAXIAL

 

 

 

 

 

 

 

 

 

 

Basic connecting procedure

1

2

3

 

 

 

AM

LOOP

1

AM Loop Antenna

AM

EXT

23

1Cut, twist and remove the insulation at the end of each speaker signal cable (not supplied).

2Open the terminal and then insert the speaker signal cable.

3Close the terminal.

Connecting the front speakers

Connect front speakers to the FRONT SPEAKERS terminals.

Outdoor single vinyl-covered wire (not supplied)

Turn the loop until you have the best reception.

Left speaker

Right speaker

Notes:

• If the AM loop antenna wire is covered with vinyl, remove the vinyl by twisting it as shown in the diagram.

• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM loop antenna connected.)

FRONT

SPEAKERS

RIGHT

LEFT

Connecting the Speakers

You can connect the following speakers:

One pair of front speakers to produce normal stereo sound.

One pair of rear speakers to enjoy the surround effect.

One center speaker to produce more effective surround effect (to emphasize human voices).

One subwoofer to enhance the bass.

IMPORTANT:

After connecting the speakers listed above, set the speaker setting information properly to obtain the best possible DSP effect. For details, see page 12.

For each speaker (except for a subwoofer), connect the (+) and (–) terminals on the rear panel to the (+) and (–) terminals marked on the speakers. For connecting a subwoofer, see page 5.

CAUTION:

Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals.

Connecting the rear and center speakers

Connect rear speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals.

 

CENTER

REAR

 

SPEAKER

SPEAKERS

Center speaker

RIGHT

LEFT

 

 

Left rear

Right rear

 

 

speaker

speaker

 

 

4

Image 7
Contents INSTRUCTIONS POWERRX-6010VBK / RX-6018VBK AUDIO/VIDEO CONTROL RECEIVERWARNING TO REDUCE THE RISK OF FIRE Caution --POWER switchAttention --Commutateur POWER Warnings, Cautions and OthersCaution Proper Ventilation For Canada/pour Le CanadaFor Canada/pour le Canada For U.S.ACOMPU LINK Remote Control System Table of ContentsBasic Settings Using the DSP Modes1 2 3 4 5 6 7 8 9 p Parts IdentificationRemote Control q w e r t yGetting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM AntennasConnecting the rear and center speakers Connecting the SpeakersBasic connecting procedure Connecting the front speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker Powered subwooferoutput Video component connectionsDVD player To audioCAUTIONS Connecting the Power CordPutting Batteries in the Remote Control Digital connectionsFrom the remote control Turning the Power On and Off StandbyBasic Operations S.WFR LFE LS S RSFrom the remote control Listening Only with HeadphonesMuting the Sound Adjusting the VolumeAdjusting the Tone Adjusting the Subwoofer Output LevelAttenuating the Input Signal Recording a Source Basic SettingsSetting the Subwoofer Information Adjusting the Front Speaker Output Balance1. Press SETTING repeatedly until Setting the Speakers for the DSP Modes1. Press SETTING repeatedly until Selecting the Analog or Digital Input Mode Digital Input DIGITAL IN Terminal Setting1. Press SETTING repeatedly until From the remote control Storing the Basic Settings and AdjustmentsUsing the Sleep Timer From the remote control ONLYUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts On the front panel To tune in a preset stationFrom the remote control Selecting the FM Reception ModeDolby Surround Dolby Digital and Dolby Pro Logic Using the DSP ModesWhat are the DSP Modes? Surround modesDAP modes Reproducing the Sound FieldAvailable DSP modes according to the input mode To activate the Surround Available DSP modesBy pressing DSP MODE By pressing SURROUND MODE5.Adjust the speaker output levels Adjusting the Surround ModesJVC Theater Surround adjustments 1. Press SURROUND MODErepeatedly until “THEATER” appears on the displayon the display Adjusting the DAP Modes1. Press SURROUND ON/OFF Activating the DSP ModesAutomatic Source Selection COMPU LINK Remote Control SystemSynchronized Recording Sound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder Operating Video ComponentsCD changer Cassette deckPOSSIBLE CAUSE TroubleshootingPROBLEM SOLUTIONharmonic distortion Specifications100 W per channel, min. RMS, driven into 8 Ω 40 Hz to 20 kHz with no more than 0.8% totalAM tuner FM tuner IHFGeneral FACTORY SERVICE CENTER LOCATIONS JVC SERVICE & ENGINEERING COMPANY OF AMERICAHOW TO LOCATE YOUR JVC SERVICE CENTER QUALITYSERVICELIMITED WARRANTY AUDIO-2 VICTOR COMPANY OF JAPAN, LIMITED 0101NHMMDWJEIN