JVC RX-558VBK manual Changing the Source Name, Setting Center and Rear Speakers for DSP Modes

Page 13

Basic Settings

Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier.

Changing the Source Name

When you have connected an MD recorder to the TAPE/MD jacks on the rear panel: Change the source name shown on the display when you select the MD recorder as the source.

On the front panel ONLY:

When changing the source name from “TAPE” to “MD”:

 

 

TAPE/MD

1.

Press TAPE/MD.

 

 

• Make sure “TAPE” appears on the display.

SOURCE NAME

2.

Press and hold SOURCE NAME

TAPE/MD

(the same button as TAPE/MD)

SOURCE NAME

until “MD” appears on the display.

To change the source name from “MD” to “TAPE,” repeat the same procedure above (in step 1, make sure “MD” appears on the display).

Note:

Without changing the source name, you can still use the connected components. However, there may be some inconvenience.

“TAPE” will appear on the display when you select the MD recorder.

You cannot use the COMPU LINK remote control system (see page 21) to operate the MD recorder.

Setting Center and Rear Speakers for

the DSP Modes

To obtain the best possible surround sound of the DSP (Digital Signal Processor) modes (see page 15), you have to register the information about the speaker arrangement after all connections are completed.

Center Speaker Setting

Register the center speaker size.

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

3. Press cursor control @/ #to select your center speaker size.

LARGE SMALL NO

LARGE: Select this mode when the size of the center speaker is the same as that of the front speakers.

SMALL: Select this mode when the size of the center speaker

is smaller than that of the front speakers.

NO: Select this mode when you do not use a center speaker.

Rear Speaker Setting

Register whether you have connected the rear speakers or not.

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Press SETTING so that the cursor

SETTING

 

control % / Þbuttons work for

 

setting the rear speaker

 

information.

 

2. Press cursor control %/ Þ repeatedly until “REAR SPK” (Rear Speaker) appears on the display.

3. Press cursor control @/ #to register whether you have connected the rear speakers.

YES: Select this mode when you use rear speakers.

NO: Select this mode when you do not use rear speakers.

Note:

On the front panel ONLY:

1. Press SETTING so that the cursor control %/ Þbuttons work for setting the center speaker size.

2. Press cursor control % / Þ repeatedly until “CNTR SPK” (Center Speaker) appears on the display.

SETTING

When you change your speakers, you need to register the information

about the speakers again.

Delay Time Setting

Register the delay time of the sound from the rear speakers, comparing the sound from the front speakers.

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

You can adjust the delay time only when you have connected the rear speakers and have set “REAR SPK” to “YES’’ (See above).

Delay time setting is only valid for ‘‘PRO LOGIC” (See page 15).

11

Image 13
Contents RX-558VBK RX-558VBK Table of Contents Parts Identification Remote ControlFront Panel To use the Cursor control buttons q on the front panelConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Setting the Voltage Selector SwitchAM Antenna ConnectionsBasic connecting procedure Connecting the SpeakersConnecting the front speakers Connecting the rear and center speakersConnecting the subwoofer speaker Connecting Audio/Video ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalVCR Video component connectionsPutting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet + to + and toFrom the remote control Turning the Power On and Off StandbyBasic Operations On the front panelSelecting the Front Speakers Muting the SoundRecording a Source Adjusting the Front Speaker Output Balance Attenuating the Input SignalAdjusting the Tone Reinforcing the BassChanging the Source Name Setting Center and Rear Speakers for DSP ModesAdjust the sound using the functions listed to the left Storing the Basic Settings Adjustments One Touch OperationUsing the Sleep Timer Press ONE Touch OperationUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Press the 10 keys to select a preset channel number Selecting the FM Reception ModePress FM/AM Press FM3D-PHONIC modes Using the DSP ModesDAP modes Surround ModesSpeaker arrangements Available DSP modes Available DSP Modes According to the Speaker ArrangementAdjusting the 3D-PHONIC Modes Adjusting the DAP Modes Press Test to check the speaker Press Rearl / + to adjustOutput balance Rear speaker output levelActivating the DSP Modes Activating the DVD Multi Playback Mode Using the DVD Multi Playback ModePress DVD Multi Remote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemSame time Automatic Source SelectionSound control section Amplifier Operating JVC’s Audio/Video ComponentsCD player TunerMD recorder Cassette deckDVD player Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsFM tuner IHF AM tunerHOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1298HIMMDWJEM