JVC RX-558VBK manual Adjusting the 3D-PHONIC Modes Adjusting the DAP Modes

Page 19

Adjusting the 3D-PHONIC Modes

Adjusting the DAP Modes

Before you start, remember...

Make sure that you have set the speaker information correctly (see page 11).

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Before you start, remember...

Make sure that you have set the speaker information correctly

(see page 11).

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

• You can only adjust the rear speaker output level when you have

On the front panel:

1. Press SURROUND repeatedly until “3DACTION” or “3D THEATR” appears on the display.

SURROUND

connected the rear speakers and have set “REAR SPK” to “YES.”

See page 11.

On the front panel:

1. Press SURROUND repeatedly

The 3D-PHONIC, PRO LOGIC indicators also light up on the display.

2. Press ADJUST so that the cursor

ADJUST

control %/ Þ/ @/ #buttons work

 

for adjusting the surround setting.

 

3. Press cursor control % / Þ repeatedly until “–EFFECT+” appears on the display.

4. Press cursor control @/ #to select an effect level you want.

• Each time you press the button, the effect level changes as follows:

EFFECT 1 EFFECT 2 EFFECT 3

EFFECT 5

EFFECT 4

As the number increases, the selected 3D-PHONIC mode becomes stronger.

SURROUND

until the DAP mode — DANCE

CLUB, LIVE CLUB, HALL, or

PAVILION — appears on the

display.

The DAP indicator also lights up on the display.

2. Press ADJUST so that the cursor

ADJUST

control % / Þ/ @/ #buttons work for adjusting the DSP setting.

3. Press cursor control %/ Þ repeatedly until “– REAR +” appears on the display.

4.Press cursor control @/ #to adjust the rear speaker output

level (from –10 to +10).

Note:

From the remote control:

1. Press SOUND CONTROL.

The 10 keys are activated for sound adjustments.

2.Press SURROUND repeatedly until “3DACTION” or “3D THEATR” appears on the display.

SOUND

CONTROL

SURROUND

3

You cannot adjust the left and right rear speaker output levels

separately.

5. Press cursor control %/ Þ repeatedly until “–EFFECT+” appears on the display.

The 3D-PHONIC, PRO LOGIC indicators also light up on the display.

3. Press EFFECT to select an effect

 

 

level you want.

 

 

 

 

EFFECT

• Each time you press the button, the effect

4

level changes as follows:

 

 

 

 

 

 

EFFECT 1

 

EFFECT 2

 

EFFECT 3

 

 

 

 

 

 

EFFECT 5

EFFECT 4

 

 

 

 

 

 

As the number increases, the selected 3D-PHONIC mode becomes stronger.

6.Press cursor control @/ #to select an effect level you want.

Each time you press the button, the effect level changes as follows:

EFFECT 1 EFFECT 2 EFFECT 3

EFFECT 5

EFFECT 4

As the number increases, the selected DAP mode becomes stronger.

17

Image 19
Contents RX-558VBK RX-558VBK Table of Contents To use the Cursor control buttons q on the front panel Remote ControlParts Identification Front PanelSetting the Voltage Selector Switch Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesConnecting the rear and center speakers Connecting the SpeakersAM Antenna ConnectionsBasic connecting procedure Connecting the front speakersIf your audio components have a Compu LINK-3 terminal Connecting Audio/Video ComponentsConnecting the subwoofer speaker Audio component connectionsVCR Video component connections+ to + and to Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletOn the front panel Turning the Power On and Off StandbyFrom the remote control Basic OperationsSelecting the Front Speakers Muting the SoundRecording a Source Reinforcing the Bass Attenuating the Input SignalAdjusting the Front Speaker Output Balance Adjusting the ToneChanging the Source Name Setting Center and Rear Speakers for DSP ModesPress ONE Touch Operation Storing the Basic Settings Adjustments One Touch OperationAdjust the sound using the functions listed to the left Using the Sleep TimerUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Press FM Selecting the FM Reception ModePress the 10 keys to select a preset channel number Press FM/AMSurround Modes Using the DSP Modes3D-PHONIC modes DAP modesSpeaker arrangements Available DSP modes Available DSP Modes According to the Speaker ArrangementAdjusting the 3D-PHONIC Modes Adjusting the DAP Modes Rear speaker output level Press Rearl / + to adjustPress Test to check the speaker Output balanceActivating the DSP Modes Activating the DVD Multi Playback Mode Using the DVD Multi Playback ModePress DVD Multi Automatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Same timeTuner Operating JVC’s Audio/Video ComponentsSound control section Amplifier CD playerMD recorder Cassette deckDVD player Problem Possible Cause Solution TroubleshootingAM tuner SpecificationsAmplifier FM tuner IHFHOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1298HIMMDWJEM