JVC RX-558VBK manual Troubleshooting, Problem Possible Cause Solution

Page 26

Troubleshooting

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

The display does not light up.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

 

 

 

No sound from speakers.

Speaker signal cables are not connected.

Check speaker wiring and reconnect if

 

 

necessary.

 

 

 

 

The SPEAKERS 1 and 2 buttons are not

Press SPEAKERS 1 and 2 correctly.

 

set correctly.

 

 

 

 

 

An incorrect source is selected.

Select the correct source.

 

 

 

 

Muting is activated.

Press MUTING to cancel the mute.

Sound from one speaker only.

Speaker signal cables are not connected properly.

Check speaker wiring and reconnect if necessary.

The balance is set to one extreme.

Adjust the balance properly (see page 9).

Continuous hiss or buzzing during FM reception.

Incoming signal is too weak.

Connect an outside FM antenna or contact your dealer.

The station is too far away.

Select a new station.

An incorrect antenna is used.

Check with your dealer to be sure you have the correct antenna.

 

Antennas are not connected properly.

Check connections.

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

reception.

 

traffic.

 

 

 

Howling during record playing.

Your turntable is too close to speakers.

Move speakers away from the turntable.

 

 

 

“OVERLOAD” starts flashing on the

Speakers are overloaded because of high

Rotate the MASTER VOLUME control

display.

volume.

counterclockwise three or four times, then

 

 

press POWER on the front panel.

 

 

If “OVERLOAD” does not disappear, unplug

 

 

the AC power cord, then plug it back again.

Speakers are overloaded because of short circuit of speaker terminals.

Press POWER on the front panel, then check the speaker wiring.

If “OVERLOAD” does not disappear, unplug the AC power cord, then plug it back again.

If speaker wiring is not short-circuited, contact your dealer.

Remote control does not work.

There is an obstruction in front of the

Remove the obstruction.

remote sensor on the receiver.

 

 

 

Batteries are weak.

Replace batteries.

24

Image 26
Contents RX-558VBK RX-558VBK Table of Contents Front Panel Remote ControlParts Identification To use the Cursor control buttons q on the front panelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Setting the Voltage Selector SwitchConnecting the front speakers Connecting the SpeakersAM Antenna ConnectionsBasic connecting procedure Connecting the rear and center speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker If your audio components have a Compu LINK-3 terminalVideo component connections VCRPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control + to + and toBasic Operations Turning the Power On and Off StandbyFrom the remote control On the front panelRecording a Source Muting the SoundSelecting the Front Speakers Adjusting the Tone Attenuating the Input SignalAdjusting the Front Speaker Output Balance Reinforcing the BassSetting Center and Rear Speakers for DSP Modes Changing the Source NameUsing the Sleep Timer Storing the Basic Settings Adjustments One Touch OperationAdjust the sound using the functions listed to the left Press ONE Touch OperationReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Press FM/AM Selecting the FM Reception ModePress the 10 keys to select a preset channel number Press FMDAP modes Using the DSP Modes3D-PHONIC modes Surround ModesAvailable DSP Modes According to the Speaker Arrangement Speaker arrangements Available DSP modesAdjusting the 3D-PHONIC Modes Adjusting the DAP Modes Output balance Press Rearl / + to adjustPress Test to check the speaker Rear speaker output levelActivating the DSP Modes Press DVD Multi Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Same time Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionCD player Operating JVC’s Audio/Video ComponentsSound control section Amplifier TunerDVD player Cassette deckMD recorder Troubleshooting Problem Possible Cause SolutionFM tuner IHF SpecificationsAmplifier AM tunerHOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1298HIMMDWJEM