JVC RX-558VBK Storing the Basic Settings Adjustments One Touch Operation, Using the Sleep Timer

Page 14

On the front panel:

1. Press SETTING so that the cursor

SETTING

 

control %/ Þbuttons work for

 

setting the delay time.

 

2. Press cursor control % / Þ repeatedly until “–DELAY +” appears on the display.

3.Press cursor control @/ #to select an appropriate delay time.

DELAY 1 DELAY 2

DELAY 3

DELAY 1: Select this mode when the distance from you to your rear speakers is greater than that to the front speakers.

DELAY 2: Select this mode when the distance from you to your rear speakers is almost equal to that to the front speakers.

DELAY 3: Select this mode when the distance from you to your rear speakers is less than that to the front speakers.

From the remote control:

1.Press SOUND CONTROL.

2.Press SURROUND repeatedly until “PRO-LOGIC” appears on the display.

3.Press DELAY repeatedly until an appropriate delay time appears on the display.

Storing the Basic Settings and

Adjustments — One Touch Operation

JVC’s One Touch Operation function is used to assign and store different sound settings for each different playing source. By using this function, you do not have to change the settings every time you change the source. The stored settings for the newly selected source are automatically recalled.

The following can be stored for each source:

Volume level (see page 9)

Input Attenuator (see page 10)

Balance (see page 10)

Bass Boost (see page 10)

Tone adjustment (see page 10)

DSP modes

3D-PHONIC mode settings (see page 17)

DAP mode settings (see page 17)

Surround mode settings (see page 18)

DVD MULTI playback mode settings (see page 20)

To store the sound settings

1. Press ONE TOUCH OPERATION.

The ONE TOUCH OPERATION lamp lights up, then the previously memorized settings are recalled.

ONE TOUCH OPERATION

ONE TOUCH

 

OPERATION

On the front panel

On the remote

2. Adjust the sound using the functions listed to the left.

The newly adjusted settings are memorized.

To recall the sound settings

With the ONE TOUCH OPERATION lamp lit, the settings for the currently selected source are recalled, when the source is selected.

To cancel the One Touch Operation function

Press ONE TOUCH OPERATION so that the lamp goes off. (Even though the One Touch Operation function is canceled, the recalled sound effects remain active.)

Notes:

If the source is FM or AM, you can assign a different setting for each band.

The DSP modes and DVD MULTI playback mode cannot be used at the same time.

Using the Sleep Timer

Using the Sleep Timer, you can fall asleep to music and know the receiver will turn off by itself rather than play all night.

From the remote control ONLY:

SLEEP

Press SLEEP repeatedly.

The SLEEP indicator lights up on the display, and the shut-off time changes as follows (in minutes):

10 20 30 40 50 60 70 80

0(Canceled)

When the shut-off time comes

The receiver turns off automatically.

To check or change the time remaining until the shut-off time

Press SLEEP once.

The remaining time until the shut-off time appears in minutes.

• To change the shut-off time, press SLEEP repeatedly.

To cancel the Sleep Timer

Press SLEEP repeatedly until “0.” appears on the display. (The SLEEP indicator goes off.)

Turning off the power also cancels the Sleep Timer.

12

Image 14
Contents RX-558VBK RX-558VBK Table of Contents Front Panel Remote ControlParts Identification To use the Cursor control buttons q on the front panelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Setting the Voltage Selector SwitchConnecting the front speakers Connecting the SpeakersAM Antenna ConnectionsBasic connecting procedure Connecting the rear and center speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker If your audio components have a Compu LINK-3 terminalVideo component connections VCRPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control + to + and toBasic Operations Turning the Power On and Off StandbyFrom the remote control On the front panelRecording a Source Muting the SoundSelecting the Front Speakers Adjusting the Tone Attenuating the Input SignalAdjusting the Front Speaker Output Balance Reinforcing the BassSetting Center and Rear Speakers for DSP Modes Changing the Source NameUsing the Sleep Timer Storing the Basic Settings Adjustments One Touch OperationAdjust the sound using the functions listed to the left Press ONE Touch OperationReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Press FM/AM Selecting the FM Reception ModePress the 10 keys to select a preset channel number Press FMDAP modes Using the DSP Modes3D-PHONIC modes Surround ModesAvailable DSP Modes According to the Speaker Arrangement Speaker arrangements Available DSP modesAdjusting the 3D-PHONIC Modes Adjusting the DAP Modes Output balance Press Rearl / + to adjustPress Test to check the speaker Rear speaker output levelActivating the DSP Modes Press DVD Multi Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Same time Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionCD player Operating JVC’s Audio/Video ComponentsSound control section Amplifier TunerDVD player Cassette deckMD recorder Troubleshooting Problem Possible Cause SolutionFM tuner IHF SpecificationsAmplifier AM tunerHOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1298HIMMDWJEM