ProForm CS user manual Hold the receiver so the small cylinder, Is oriented as shown and is facing

Page 11

12.Raise the Frame (56) to the position shown.

Have a second person hold the Frame until this step is completed.

Orient the Storage Latch (53) so that the large barrel and the Latch Knob (54) are oriented as shown.

Attach the Latch Bracket (27) and Storage Latch (53) to the Base (83) with two 3/8" x 2" Bolts (4) and two 3/8" Nuts (8).

Attach the upper end of the Storage Latch (53) to the bracket on the Frame (56) with a 3/8" x 2" Bolt (4) and a 3/8" Nut (8). Note: It may be nec- essary to move the Frame back and forth to align the Storage Latch with the bracket.

Lower the Frame (56) (see HOW TO LOWER THE TREADMILL FOR USE on page 21).

12

56

 

 

 

8

453

 

54

 

Large

 

Barrel

 

27

83

 

8

4

 

 

13.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used to adjust the walking belt (see pages 23 and 24).

If you purchase the optional chest pulse sensor (see page 19), follow the steps below to install the re- ceiver included with the chest pulse sensor.

1.Make sure that the power cord is unplugged. Remove the indicated 1/2" Screws (1) and the Access Door (87) from the Console Back (91).

2. Connect the wire on the receiver (A) to the indi-

91

 

Small

 

cated wire extending from the Console Back

 

 

(91). Hold the receiver so the small cylinder

 

87

Screws A

is oriented as shown and is facing the

Wire

Console Back. Attach the receiver to the plastic

 

 

 

posts on the Access Door (87) with the two in-

 

 

 

Small

cluded small screws.

 

 

1

3. Make sure that no wires are pinched.

 

 

Cylinder

Reattach the Access Door (87) with the 1/2"

 

 

 

 

Screws (1). Discard the other wires included

 

 

 

 

with the receiver.

 

 

 

 

11

Image 11
Contents Model No. PFTL79108.0 Serial No QUESTIONS?Table of Contents Pulse sensor is not a medical device Important PrecautionsPage Before YOU Begin Assembly Nut the Wheel must turn freely. Discard See the inset drawing. Tie the wire tieBolt and Nut will be used in the next as Careful not to pinch the Upright WireDo not fully tighten the Bolts yet Not fully fold the Frame yetView a Console Ground Wire 101 Is oriented as shown and is facing Make sure that no wires are pinchedHold the receiver so the small cylinder PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramStart the walking belt and adjust the speed HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeStand on Seconds When you are finished exercising, removeAdjust the incline of the treadmill to the lowest Follow your progress with the displayFollow your progress with the display. See on HOW to USE a Personal Trainer WorkoutSelect a personal trainer workout HOW to USE the Ifit Competition Training Center Enter user information HOW to USE the Settings ModeSelect the settings mode Measure your heart rate if desired. See onOptional Chest Pulse Sensor Information ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Compatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Top Problem The walking belt slows when walked onProblem Solution Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description Part LIST-Model No. PFTL79108.0104 Lift Motor Spacer Userʼs Manual Exploded Drawing A-Model No. PFTL79108.0 R0708A Exploded Drawing B-Model No. PFTL79108.0 R0708A Exploded Drawing C-Model No. PFTL79108.0 R0708A Exploded Drawing D-Model No. PFTL79108.0 R0708A Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty