ProForm CS user manual Troubleshooting, Compatible with GFCI-equipped outlets

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 12. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has tripped.

 

 

To reset the circuit breaker, wait for five minutes

Tripped

Reset

and then press the switch back in.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. Hold down the Stop button and the Speed increase button, insert the key into the console, and

then release the Stop button and the Speed increase button. Press the Incline increase or de-

crease button. The treadmill will automatically rise to the maximum incline level and then return to

the minimum level. This will recalibrate the incline system. If the incline does not calibrate, press

the Stop button, and then press the Incline increase or decrease button again. When the incline

is calibrated, remove the key from the console.

 

 

PROBLEM: The displays of the console do not function properly

 

 

SOLUTION: a. Remove the key from the console and UNPLUG

a

74

THE POWER CORD. With the help of a second

person, carefully tip the Uprights (74, 78) down.

 

 

There may be two #8 x 2" Screws (105) in the bot-

 

 

tom of the Belly Pan (73). If there are, remove

 

 

them. Note: A Phillips screwdriver with a shaft at

78

73

least 5 in. (13 cm) long is required. Then, raise the

Uprights.

 

105

 

 

 

 

105

22

 

 

Image 22
Contents QUESTIONS? Model No. PFTL79108.0 Serial NoTable of Contents Important Precautions Pulse sensor is not a medical devicePage Before YOU Begin Assembly See the inset drawing. Tie the wire tie Nut the Wheel must turn freely. DiscardNot fully fold the Frame yet Careful not to pinch the Upright WireDo not fully tighten the Bolts yet Bolt and Nut will be used in the next asView a Console Ground Wire 101 Hold the receiver so the small cylinder Make sure that no wires are pinchedIs oriented as shown and is facing HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Start the walking belt and adjust the speedFollow your progress with the display Seconds When you are finished exercising, removeAdjust the incline of the treadmill to the lowest Stand onSelect a personal trainer workout HOW to USE a Personal Trainer WorkoutFollow your progress with the display. See on HOW to USE the Ifit Competition Training Center Measure your heart rate if desired. See on HOW to USE the Settings ModeSelect the settings mode Enter user informationInformation Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. PFTL79108.0 Key No. Qty Description104 Lift Motor Spacer Userʼs Manual Exploded Drawing A-Model No. PFTL79108.0 R0708A Exploded Drawing B-Model No. PFTL79108.0 R0708A Exploded Drawing C-Model No. PFTL79108.0 R0708A Exploded Drawing D-Model No. PFTL79108.0 R0708A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT