ProForm 1800 user manual Symptom The walking belt slows when walked on

Page 31

Locate the Reed Switch (52) and the Magnet (50) on the left side of the Pulley (49). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If neces- sary, loosen the #8 x 3/4" Tek Screw (14), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (not shown) and run the treadmill for a few minutes to check for a correct speed reading.

b.If the walking belt is overtightened, treadmill per- formance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

52

14

1/8 in.

Top

View

49

50

b

2–3 in.

SYMPTOM: The incline of the treadmill does not change correctly

a.Calibrate the incline system (see step 4 on page 26).

SYMPTOM: The walking belt slows when walked on

a.Use only a surge suppressor that meets all of the specifications described on page 16.

Idler Roller Screws

c.Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform unless instructed to do so by an authorized service representative. Such substances may deterio- rate the walking belt and cause excessive wear. If you suspect that the walking belt needs more lubricant, see the front cover of this manual.

d.If the walking belt still slows when walked on, see the front cover of this manual.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL11011.0 Serial No Call TOLL-FREETable of Contents Important Precautions Page Before YOU Begin Part Identification Chart Make sure that the power cord is unplugged AssemblyTighten the Screws yet. Note Use the short hex See the inset drawing. Tie the wire tieAttach the Right Upright not shown Base Covers into place yet Page Page Console Assembly Make sure to follow all Instructions in this step Raise the Frame 56 to the position shown Press the Grommet 77 into the square hole in the Base HOW to Connect the Power Cord Operation and AdjustmentUse a Surge Suppressor Features of the Console DiagramConsole HOW to USE the Touch Screen HOW to Turn on the PowerCreate an iFit Live account HOW to SET UP the ConsoleConnect to your wireless network Check for firmware updates Calibrate the incline systemHOW to USE the Manual Mode Key from the console When you are finished exercising, removePower cord. Important If you do not do Measure your heart rate if desiredSelect an onboard workout HOW to USE AN Onboard WorkoutStart the workout Select the main menu. See on Select a set-a-goal workout HOW to USE a SET-A-GOAL WorkoutStart the workout. See on HOW to USE AN Ifit Live WorkoutHOW to USE the Equipment Settings Mode Find keycodes HOW to USE the Maintenance ModeExit the maintenance mode Calibrate the incline system of the treadmillExit the wireless network mode HOW to USE the Wireless Network ModeEnable Wi-Fi Set up and manage a wireless network connectionMake sure that the audio wire is fully plugged HOW to USE the Stereo Sound SystemHOW to USE the Internet Browser HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Move the TreadmillSymptom The power turns off during use TroubleshootingSymptom The walking belt slows when walked on Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesQty Description Part ListDescription Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents